520106

Atika AMA2500 Manual

14
Zoom out
Zoom in
Previous page
1/128
Next page
12
On / Off switch
Do not use any device where the switch can not be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
Switch on
Press the green button I .
Switch off
Press the red button 0 .
Restart protection in case of power
failure
In case of a power failure, the device switches off automatically
(zero-voltage initiator). To restart, press the green button again.
Motor protection
The motor is equipped with a safety switch and switches off au-
tomatically when overloaded. After a cooling-down break (approx.
5 min), the motor may be restarted. Press the
1. reset button (motor protection)
2. green button I to restart.
Electrical mains supply impedance
When conditions in the electrical mains supply are un-favourable,
voltage reductions for short periods can occur during the process
of turning on the equipment, which can adversely affect other
equipment (e.g., the flickering of a lamp).
No breakdowns are to be expected if the maximum, electrical
mains supply impedances given in the table are met.
Power consumption P1 (W) Electrical mains supply
impedance Zmax (W)
2300 0,24
2500 0,24
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
g
g
a
a
r
r
d
d
e
e
n
n
s
s
h
h
r
r
e
e
d
d
d
d
e
e
r
r
Choose a working position alongside the equipment or behind
it. Never stand near the ejection opening.
Longer material that is protruding from the device could
spring back when it is drawn in by the blades! Observe safety
distance!
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into the
filler funnel, ejection channel or in the vicinity of other moving
parts.
Check that no chopped residues are in the filling hopper be-
fore switching on the equipment.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones, bottles
or other objects unintended for processing, enter the filling
hopper.
Immediately switch off the equipment and allow it to come to a
stop, if foreign objects enter the filling hopper or if the equip-
ment starts to make unusual noises or vibrates. Remove the
mains plug and carry out the following checks:
− inspect for damage,
− replace or repair damaged parts,
− check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
• organic household and garden waste
e. g. hedge and tree cuttings, dead flowers and vegetable
kitchen waste.
No:
• glass, metal, plastic, plastic bags, stones, cloth, roots with
soil, food left-overs, fish or meat.
Special tips on shredding:
¾ Branches, twigs and wood should be broken down immediate-
ly after they have been cut.
− Material of this kinds gets very hard when it is dry, and the
maximum allowed branch diameter to be processed has to
be reduced.
¾ Remove any side shoots from branches with a large number
of twigs.
¾ How to shred garden and kitchen waste with hight water con-
tent and a tendency to clog
− to prevent the machine from clogging, alternate waste with
wood containing material.
¾ Do not allow the shredded material to pile up too high in the
area of the ejection opening. This can lead to shredded mate-
rial blocking the ejection channel, and backing up to the filler
opening.
¾ Clean out the filler opening and ejection channel thoroughly if
the machine becomes blocked. Before doing this, switch the
motor off and disconnect the machine from the mains power
supply.
¾ Please do not exceed the maximum branch diameter speci-
fied (cutting fresh wood) for your appliance (∅ see “Technical
data”). Depending on the wood’s nature and freshness the
maximum branch diameter the machine can process may be
smaller.
Reset button
(motor protection)
ON
OFF
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika AMA2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika AMA2500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info