555721
17
Zoom out
Zoom in
Previous page
1/44
Next page
On/Off switch D1
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
16
Switching on
Press the green button ( I ) on the switch.
If there is a power cut, the machine switches off
automatically. Push the green ( I ) button to start the
machine again.
Switching off
Press the red button. ( 0 )
EMERGENCY-STOP button
In an emergency case, the surface planing and
thicknessing machine can be cut off by pressing the
EMERGENCY-STOP button (21).
Motor protection (230 V only)
The motor is equipped with a safety switch and switches
off automatically when overloaded.
It can be switched back on following a cooling off phase
(5 – 10 min).
Press the
1. red button ( 0 ).
2. the small button next to the button (20)
3. the green button ( I ) to start
Machine with 4
Ensure that
00 V 3~
the rotating
otating direction
ou can change the direction by
ust / chip exhaustion
direction of the blade shaft
matches the rotating
direction indicated on the
machine.
R
Y
placing a screw-driver in the slot
provided in the plug collar, and
adjust the correct direction by
moving to the left or right applying
slight pressure.
D
The wood dust generated during operation impedes the
Ther e
necessary view and is harmful to health to some degree.
efore, always connect the shavings bag (19) to th
asis.
hood (27) is
shavings exhauster connector (16). C6 - C7
Empty the shavings bag on a regular b
The motor will only start if the extractor
properly attached and thus releases the safety switch.
Working with the surface planing and
thicknessing machine
Before starting to work consider the following safety
W
ing and thicknessing machine securely
he blade shaft?
have
advices to keep the risk of injuries as small as
possible.
orkplace tidied?
Is the surface plan
installed?
Are all fastening screws tightened?
Are the blades securely fastened on t
whether the pushstick is to hand
e machine until you
You may not start to operate th
read these operating instructions, observed all the
instructions given and installed the machine as described!
Also, note the following important points:
de shaft is
ers closed.
free
Make sure that the non-used area of the bla
covered by the blade shaft guard.
Place yourself outside of the area of danger.
Place your hands flat on the workpiece with fing
Never remove loose splinters, chips, or similar by hand.
Connect the shavings bag.
ollers and cutting tools are
Make sure that the feed r
from wood shavings and dust.
Do only machine workpieces the dimensions of which are
within the specifications for this machine (see “Technical
data”).
Do not guide back the workpiece over the open-running
blade shaft.
Adjust the smallest cutting depth after your work is finished.
Observe all safety instructions in any case.
e planing is to smooth a rough surface
Surface planing
The objective of surfac
(planing), e.g. to smooth the edge of a board.
For this the workpiece is placed onto the feed table plate and is
machined on its underside. Feed direction is from right to left.
Preparations:
Pull the mains plug before performing
settings.
Installing the dust extractor
1. os crank handle (25) and Lo en the locking wheel (24) on the
turn the latter anticlockwisely to move the thicknessing table
plate to its lowest position. E2 - E3
Slide the shavings exhauster hood (27
2. ) under the feed table
plate. Slide two fixing brackets in the grooves of the table
plate. E4 - E5
Make sure that
3. the shavings exhauster hose and the bag
are secured.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ADH 254 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ADH 254 A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atika ADH 254 A

Atika ADH 254 A Installation Guide - English, German, Dutch, French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info