519288

Atika ABS 2000 Manual

17
Zoom out
Zoom in
Previous page
1/85
Next page
16
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points.
Local regulations – especially regarding protective
measures – must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer
service points.
Use only original spare. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
Screw on both side parts (1+2).
For each side part you require:
2 cup square screws M 8 x 40
2 combi nuts M 8
Screw on the transverse joint (4).
For the connection you require:
4 cup square screws M 8 x 10
4 combi nuts M 8
Put the pre-assembled device unit on the side
parts.
Fix first one side with each 2 round-head screws
M 5 x 16 and hexagon nut M 5.
Now fix the other side.
Then, fasten the four screw connections.
Put on the extraction hose (7).
Fasten the extraction hose by refastening the screw
on the hose clip (17) a few revolutions.
Put on the saw dust collecting bag (14).
Fasten the saw dust collecting bag by attaching the
quick release fastener (6).
Hang in the bag suspension (9).
Put on the filter bag (15).
Fasten the filter bag by attaching the quick release
fastener (6).
Hang in the filter bag.
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Check that the machine is completely and correctly
assembled.
Put the saw dust extraction system on a place which
meets the following requirements:
− firm and even ground
− free of risks of stumbling
− sufficient light and air conditions
Before using the machnine, make sure each time that
− there are no faulty connections (tears, cuts, etc.)
Do not use any defective cables.
− there are no damage at the machine (see safety
advices)
− all screws are tight
Mains connection
Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the
machine to the relevant and properly earthed plug.
Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (FI switch 30 mA).
Only use connection cables with sufficient diameters.
Mains fuse: 10 A
Static charge
The complete extraction system is assembled of non-
electro-conductive components.
Do not replace synthetic parts by metallic parts.
Particularly, the extraction hose must not feature a
metallic coil.
When the extraction hose is fastened on electro-
conductive parts (e.g. metallic suction hoods or
tubes) these must be grounded for the discharge of
possibly appearing electrostatic energy.
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be
repaired or replaced immediately by the customer
service.
Switch on
Press the green button
( I ) on the switch.
Switch off
Press the red button
( 0 ) on the switch.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ABS 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ABS 2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info