519873

Atika 2300 W Manual

14
Zoom out
Zoom in
Previous page
1/123
Next page
Setting the clearance.
Switch on the device.
There is an adjustment device on the right hand side of the plastic housing. To adjust the distance turn the adjusting knob (D)
clockwisely so that the screw (C) moves toward the cutting roller. Turn until fine aluminium chips are falling from the ejection slot.
13
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
• Each time before starting maintenance work:
− Switch off the motor and pull out the mains plug.
− Wear protective gloves to prevent injury.
The cutters will not come to a standstill immediately after cut-off. Before starting any service work wait until all parts are sta-
tionary.
Be sure to have removed any tools from the machine after completion of service work.
• Generally garden shredders require little maintenance. To maintain their efficiency and a long life, observe the following:
− Keep vent slits clean and free from obstructions.
− Check the locking screws (tighten where necessary).
− Clean the device after shredding.
To clean your product only use a warm moist cloth and a soft brush.
Never use cleaning agents or solvents. Otherwise the device may be damaged irreversibly. Plastic parts may be corroded by chemi-
cals.
− Do not clean the machine with running water or high-pressure cleaners.
−
−
After each operation treat bare metal parts with an environment-compatible biodegradable spray oil to protect them against corro-
sion.
− the cutting roller and shaving plate are expendable parts, though with normal use and correct adjustment they have a service life of
many years
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
a
a
l
l
f
f
a
a
u
u
l
l
t
t
s
s
Before each fault elimination:
− Switch off device.
− Wait for standstill of the device.
− Pull out mains plug.
Fault Possible cause Remedy
Motor does not start - Rotation selector switch on position “0”
- No power supply
- Mains cable defective
- Machine overloaded (motor protection)
- Switch off device and switch over direction of rotation
selector switch.
- Check fuses
- have these checked (electrician)
- Allow the device to cool down.
Press the
1. reset button (motor protection)
2. green button I to restart.
Motor hums but does not
start
- Cutting roller blocked
- Capacitor faulty
- Switch off the device.
Turn the direction of rotation selector switch into
position
. Switch on device until the jam has been
cleared. Switch device off again. Turn back the
direction of rotation selector switch to position
.
- Bring machine to manufacturer or authorised work-
shop for repair
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika 2300 W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika 2300 W in the language / languages: English, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info