109803

ATAG WU 1511 PX Manual

17
Zoom out
Zoom in
Previous page
1/34
Next page
GB 12 GB 13
assembly (continued)
building in the extractor hood
1. Remove the edge-extractor panel:
- Flip the edge-extractor panel downwards.
- Release the latch cables by turning the bayonet catch
180 degrees.
- Disconnect the connectors from the electricity cables.
- Remove the edge-extractor panel from the extractor
hood.
2. Put the plug of the extractor hood in the socket.
3. Connect the 7-pole connector to the 7-pole connector of
the external motor (WU1511PX).
4. Position the extractor hood in the hole and slide the 4
sliding pieces outwards from inside the hood. The
extractor hood should remain hanging.
5. Secure the extractor hood to the joists using the screws
provided and the holes intended for this purpose.
6. Refit the edge-extractor panel. Do not forget to
reconnect the connectors of the electricity cables.
GB 12
assembly (continued)
preparing the hole
1. Determine the position of the hole in the ceiling or in the
chimney with respect to the cooking plate.
2. The extractor hood is fit with a temporary suspension
system with sliding pieces to make mounting easier. To
use this system, the hole should be fit with a suspension
edge for temporary hanging (height: maximum 40 mm;
see diagram).
Note: the mounting must be sturdy enough to bear the
weight of the extractor hood at 4 points.
3. The ceiling/chimney must have a joisted layer with a
minimum thickness of 36 mm to which the extractor hood
can be attached using the 4 screws (see picture).
Account for the position of the fastening holes (see hole
pattern on page 11).
For upward extraction, the joists should preferably run
parallel with the short sides. When using the optional flat
duct system, the joists must run parallel with the direction of
extraction.
ceiling/chimney
extractor hood
joisted layer
suspension edge
sliding piece
technical data
type number: see data plate in the hood
power supply: 230 V - 50 Hz
connected load: see data plate
dimensions (h x w x d): see "fitting dimensions"
approvals mark: Kema
This appliance complies with the CE directives.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG WU 1511 PX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WU 1511 PX in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info