Manual ATAG ws 9011 mx (page 15 of 38) (English, German, Dutch, French)

133423

Zoom out

Zoom in

1/38

GB 7

solution

Change the light bulb.

- Gently press the front side of

the window (1) and it should

tilt open slightly (2).

- Open the window fully and

fit a new 20 W halogen bulb.

Note: do not touch the bulb’s

glass with your fingers.

- Gently push the window

closed again.

Change the discharge duct

(see installation instructions).

Phone the Service department.

cause

Lamp defective.

NB:

Only use the same type of lamp

with the wattage stated.

Discharge duct too long or has

too many bends.

Motor defective.

Motor or controls defective.

Connection lead defective.

fault

Lighting does not work.

Extractor hood makes a lot of

noise.

No extraction.

faults

Please check the following points which may solve the problem, before calling the service

department.

If the connection cable is damaged, it should be replaced by the service department of the

manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

NB: Disconnect the appliance from the mains before starting any repairs, preferably by removing

the plug from the socket or by setting the isolation switch to zero.

GB 6

carbon filter indicator (optional)

switching on the carbon filter indicator

If you use the recirculation extractor hood, you must use a

carbon filter. In that case, you can switch on the carbon

filter indicator. Press keys

OFF

and

for approx. 5

seconds in order to switch on the carbon filter indicator.

The 4 green LEDs light up and the extractor hood gives an

audible signal.

replacing the carbon filter

If the 2

red LED in the control panel starts to flash, clean

the filter immediately. Place a new carbon filter and erase

the electronic memory by pressing the

button for

approx. 5 seconds. The 2

red LED stops flashing.

switching off the carbon filter indicator

Press keys

OFF

and

12h

for approx 5 seconds in order to

switch off the carbon filter indicator. The 4 green LEDs light

up and the extractor hood gives an audible signal.

You can check if the carbon filter is switched on by pressing

the keys

and

12h

continuously for approx 5

seconds. When the carbon filter indicator is switched on the

4 green LEDs light up, otherwise the 4 red.

As you press a key, a key signal sounds in confirmation.

Press keys

12h

for 3 seconds continuously on

the in order to switch on the key signal.

Repeat this procedure if you wish to switch off the key

signal again.

OFF ON 12h

switch off the key signal

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ws 9011 mx in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATAG ws 9011 mx Manual

Product: