Manual ATAG WS 6011 IM (page 11 of 12) (English, German, Dutch, French)

121750

Zoom out

Zoom in

1/12

it to the ceiling using the screws A (Fig.3) in such a way that

it is in line with your hood and respecting the distance from

the ceiling indicated in Fig.2. Connect the  ange C to the air

exhaust hole using a connection pipe (Fig.4).

Insert the upper  ue into the lower  ue. Fix the lower  ue to

the hood using the screws B provided (Fig.4), extract the up-

per  ue up to the bracket and  x it with the screws B (Fig.3).

To transform the hood from a ducting version into a  ltering

version, ask your dealer for the charcoal  lters and follow the

installation instructions.

• Filtering version

Install the hood and the two flues as described in the

paragraph for installation of the hood in ducting version. To

assemble the  ltering  ue refer to the instructions contained

in the kit. If the kit is not provided, order it from your dealer

as accessory. The charcoal  lters must be  tted in the ducting

unit located inside the hood (Fig.7).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cook-

ing.

It is recommended to leave the appliance in operation for 15

minutes after cooking is terminated in order to completely

eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned by

the regularity of the maintenance operations, in particular,

the active carbon  lter.

• The anti-grease  lters capture the grease particles suspended

in the air, and are therefore subject to clogging according to

the frequency of the use of the appliance.

In order to prevent  re hazard, it is recommendable to clean

the  lter at a maximum of 2 months by carrying out the fol-

lowing instructions:

- Remove the  lters from the cooker hood and wash them

in a solution of water and neutral liquid detergent, leaving

to soak.

- Rinse thoroughly with warm water and leave to dry.

- The  lters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes.

This is not cause for customer complaint nor replacement

of panels.

• The active carbon  lters purify the air that is replaced in the

environment. The  lters are not washable nor re-useable and

must be replaced at maximum every four months. The satura-

tion of the active carbon  lter depends on the frequency of

use of the appliance, by the type of cooking and the regularity

of cleaning the anti-grease  lters.

• Clean the fan and other surfaces of the cooker hood regu-

larly using a cloth moistened with denatured alcohol or non

abrasive liquid detergent.

• The illumination installation is designed for use during

cooking and not for prolonged general illumination of the

environment. Prolonged use of the illumination installation

notably reduces the duration of the bulb.

• Commands: (Fig.5)

Push-button A = on/o lights switch

Push-button B = on/o cooker hood switch. The appliance

switches on at speed level 1, If the cooker hood is on depress

the push-button for 2 sec. to switch o the cooker hood. If

the cooker hood is at speed level 1 it will not be necessary

to depress the push-button to switch the cooker hood o .

Decreases the motor speed.

Display C = indicates the motor speed level selected and

activates the timer.

Push-button D = switches on the cooker hood. Increases the

motor speed. Touching the key at 3rd speed, the intensive

function runs for 10’, then the appliance go back to work at the

original speed. During this function the display blinks.

Key E = The Timer times the functions on activation for 15

minutes, after which they are switched o . The Timer is deac-

tivated by re-pressing Key E. When the Timer is activated the

decimal point must  ash on the display. The Timer cannot be

activated if the intensive speed is functioning.

The “clean air” function is activated by pressing key E for 2

seconds when the appliance is switched o . This switches the

motor on for 10 minutes every hour at the  rst speed. During

functioning a rotary movement of the peripheral segments

must be visualised on the display. When this time has passed

the motor switches o and the  xed letter “C” must be visu-

alised on the display until the motor re-starts after 50 minutes

for another 10 minutes and so on. Press any key apart from

the light keys to return to normal functioning. Press key E to

deactivate the function.

• Active carbon/grease  lter saturation:Fig.5

- When display item C  ashes, at a speed where it alternates

with the letter F (e.g. 1 and F), the grease  lters must be

washed.

- When display item C  ashes, at a speed where it alternates

with the letter A (e.g. 1 and A), the carbon  lters must be

replaced.

After the clean filter has been positioned correctly, the

electronic memory must be reset by pressing button A for

approximately 5 sec

onds

, until the indication F or A shown

on the display C stops  ashing.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

- 12 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WS 6011 IM in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATAG WS 6011 IM Manual

Product: