133422

ATAG ws 1211 mx Manual

19
Zoom out
Zoom in
Previous page
1/38
Next page
GB 15GB 14
assembly (continued)
Suspend the motor module on the threaded ends (1). Screw
the nuts on. Make sure that the motor module is exactly level.
Drill holes (2 x ø 6 mm) and secure the motor module with the
fixing pins supplied (6 x 60) (2).
Fit the discharge duct.
Connect the motor module electrically.
For appliances with an external motor:
Remove the screws (3) from the connector box. Run the
external motor wiring through the pull relief of the connector
box. Connect the wires according to the wiring diagram on the
motor casing and the external motor. Attach the connector
box to the motor casing (3).
fitting the hood
Fit the hood to the motor module. First hook the rear of the
hood into the motor module at the bottom (1).
Then lift the front up (2) so that the two bolts supplied (M5 x
12) can be screwed in (3). Use these bolts to level the hood.
Use these screws to level the hood.
Make the plug connections in the hood.
1
1
2
3
3
2
3
assembly (continued)
installation wall hood
The most important dimensions are shown on the previous
page. You can set the height of the telescopic pipe. Take the
allowable tolerances into account. Position the discharge
and the electrical connection in such a way that it will be
easy to hook up the hood.
Remove the transport safety device prior to assembly, see
page 12.
marking out and fitting fixing materials
Draw a vertical centre line on the wall (centre of the
extractor hood).
Place the fastening clip against the wall so that it rests
against the ceiling. The arrow on the flanged rim indicates
the middle of the cooker hood. Mark the attachment holes to
be drilled. Drill the holes (ø 8 mm).
Put the plugs into the wall and fix the fixing bracket to the
wall with the screws supplied (5 x 50 mm).
marking out and fitting motor module
Mark the position of the underside of the hood on the wall
(bear in mind the minimum distance to the hob). Mark the
(vertical) centre line.
Fold or cut the template depending on type and mark the
upper fixing holes.
Drill the fixing holes (2 x ø 10 mm).
Fix the plugs. Screw two nuts onto the threaded ends in the
opposite direction. Screw the threaded ends into the wall
leaving 20 mm projecting (see illustration). Remove the nuts.
20
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG ws 1211 mx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ws 1211 mx in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info