556998

ATAG VA6311SF Manual

26
Zoom out
Zoom in
Previous page
1/60
Next page
Problem Possible solution
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on. Close the water tap and contact the Service.
After the checks are completed, activate
the appliance. The programme continues
from the point of interruption.
If the problem occurs again, contact the
Service.
If the display shows other alarm codes,
contact the Service.
If the washing and drying
results are not satisfactory
Whitish streaks or bluish layers on
glasses and dishes
• The released quantity of rinse aid is too
much. Adjust the rinse aid selector to a
lower position.
• The quantity of detergent is too much.
Stains and dry water drops on glasses
and dishes
• The released quantity of rinse aid is not
sufficient. Adjust the rinse aid selector to
a higher position.
• The quality of the detergent can be the
cause.
Dishes are wet
• The programme is without a drying phase
or with a low temperature drying phase.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the
cause.
• The quality of the combi detergent tablets
can be the cause. Try a different brand or
activate the rinse aid dispenser and use
rinse aid together with the combi deter-
gent tablets.
Refer to ‘HINTS AND TIPS’ for other
possible causes.
Activating the rinse aid dispenser
with the multitab function activated
1. Press the on/off button to activate the
appliance. Make sure that the appliance
is in setting mode. Refer to ‘SETTING
AND STARTING A PROGRAMME’.
2. Press and hold function buttons (B) and
(C) at the same time until the indicators
above function buttons (A), (B) and (C)
start to flash.
3. Press function button (B) .
• The indicators above function buttons
(A) and (C) go off.
• The indicator above function button
(B) continues to flash.
• The display shows the current setting
of the rinse aid dispenser.
Off
On
4. Press function button (B) to change the
setting.
5. Deactivate the appliance to confirm the
setting.
6. Adjust the released quantity of rinse aid.
7. Fill the rinse aid dispenser.
TECHNICAL INFORMATION
Dimensions Width / Height / Depth (mm) 596 / 818 - 898 / 575
Electrical connection Refer to the rating plate.
Voltage 220-240 V
Frequency 50 Hz
Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 )
Water supply
1)
Cold water or hot water
2)
max. 60 °C
Capacity Place settings 12
26
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG VA6311SF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG VA6311SF in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info