75793
19
Zoom out
Zoom in
Previous page
1/24
Next page
When the appliance is correctly levelled, the
door will not catch on either side of the cabi-
net .
If the door does not close correctly, loosen
or tighten the adjustable feet until the ma-
chine is perfectly level.
Water connection
Water inlet connection
This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we
advise you use a cold water supply.
A hot water supply is not always efficient with
heavily soiled crockery as it shortens the
washing programmes a lot.
For making the connection itself, the cou-
pling nut fitted to the machine’s inlet hose is
designed to screw onto a 3/4" gas thread
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the "Technical data". Your local Wa-
ter Authority will advise you on the average
mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being con-
nected.
The dishwasher features inlet and drain ho-
ses which can be turned either to the left or
the right to suit the installation by means of
the locknut. The locknut must be
correctly fitted to avoid water leaks.
Attention! NOT all models of dishwash-
ers have inlet and drain hoses provided
with a locknut. In this case, this facility is
not available.
If the machine is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few mi-
nutes before connecting the inlet hose.
DO NOT use connection hoses which
have previously been used on an old ap-
pliance.
This appliance has been fitted with
safety features which will prevent the
water used in the appliance from return-
ing back into the drinking water system.
This appliance complies with the appli-
cable plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water in-
let hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the wa-
ter inlet hose starts to leak during this opera-
tion, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
If water inlet hose or the safety valve is
damaged, remove the mains plug
immediately.
A water inlet hose with safety valve must
only be replaced by the Service Force
Centre.
Warning! Dangerous voltage
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink run-
ning into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
The waste connection must be at a maxi-
mum height of 60 cm from the bottom of the
dishwasher.
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG VA 6311 AF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG VA 6311 AF in the language / languages: English as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG VA 6311 AF

ATAG VA 6311 AF Additional guide - Dutch - 2 pages

ATAG VA 6311 AF User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info