328401

ATAG ox30 c Manual

56
Zoom out
Zoom in
Previous page
1/66
Next page
GB 56
how to use your oven
delaying the cooking
Carry out the same procedure as for programmed cooking. After setting the
cooking time.
Press the "end of cooking" , touch control; the time for the end of
cooking is indicated and flashes, as does the symbol to
indicate that it may be adjusted.
example :
It is 12.30.
You have programmed a cooking time of 30 min.
The end of cooking time indicated is 1 pm (13.00).
Adjust the end of cooking time using the
+or -touch controls.
example :
End of cooking time: 2 pm (14.00).
Once the end of cooking time has been programmed, the end of cooking
symbol stops flashing.
The oven will now start heating up in time for cooking to be finished by 2
pm (14.00).
When cooking finishes the oven gives a series of beeps for a few minutes.
To switch the beeps off, press the START/STOP touch control for one sec-
ond.
NOTE: You may consult or change the end of cooking time at any time by
pressing the .
To cancel your program, press the START/STOP touch control.
how to use your oven
using the timer
Your oven is fitted with an electronic timer for your use other than in
conjunction with the oven.
ATTENTION: This program is separate from the oven. It cannot be used
to stop automatic cooking. This program may never-theless
be used even when the oven is in use. In this case, the timer display
takes priority over the clock display.
Press the timer touch
.The display flashes and the timer sym-
bol appears and flashes.
Press the
+ or - touch controls to obtain the length of time
required (up to 59 minutes and 59 seconds).
The display stops flashing after a few seconds and the timer starts, counting
down the time in seconds. When the time is up, the timer bleeps to warn you
and the symbol flashes.
Stop the bleeping by pressing the touch control or START/STOP.
Normal time is now displayed.
NOTE: You may change the remaining time at any point by pressing the
touch control and using the
+ or
-
touch controls. To
cancel the timer program, set the time at
0.00 and press START/STOP.
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG ox30 c at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ox30 c in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info