446360
9
Zoom out
Zoom in
Previous page
1/18
Next page
16
GB
*Finally make the electrical connections.
Mounting the chimney (when present)
The adjustable section at the top end of the
chimney allows you to set the correct height.
Take into account the maximum tolerances
(615 - 1210 mm).
*Draw the location of the profile A by copying
the shape of the chimney (fig 11).
*Attach profile A to the ceiling and the wall
using thetwo screws provided.
*Attach the outlet pipe.
*Attach the chimney to the sides of the
profile and the to the fixing brackets (B)
on top of the hood using the screws
provided (fig. 11).
Wall cupboard fitting
*Using the appropriate drilling jig drill four
holes in the base of the wall cupboard and
cut the ventilation hole if the extractor is to
be used in Discharging mode (if the
appliance is to be used in Filtering mode
this hole is not necessary).
*Holding the extractor hood against the base
of the cupboard secure it in place using the
four screws supplied (fig. 6).
*Then make the electrical connections.
Important:
Check the position of screw A (fig. 9 and 10).
For the Discharging mode screw A must be
screwed tight; for the Filtering version the
screw must be completely loose to allow the
extracted air to escape via the top openings.
15
GB
Changing the carbon filter/
anti-grease filter
If the extractor hood is used in filtering mode
it is necessary for the active charcoal fibre
panel (fig. 1F and 9F) to be replaced
approximately every six months according to
use.
*Remove the anti-grease grill as described
under “Filtering/discharging conversion”.
*Lift the two metallic stops (fig. 9C and 10C).
*Remove the carbon filter panel
(fig. 9F and 10F).
*The anti-grease panel must be changed
according to use. If the panel is a metallic
one it can be cleaned by hand with neutral
detergent or in a dishwasher.
Changing the light bulbs
To gain access to the light bulb(s) remove the
anti-grease grille as described above and
remove the bulb(s). Replace with light bulbs
of the same type.
Installation
Before assembling the appliance it is
necessary to remove the anti-grease grille.
To install the appliance for the Discharging
mode, connect one of the two discharge
outlets to the external duct and seal off the
other opening with the cap supplied (fig. 4.).
For the Filtering mode both of the discharge
outlets of the appliance must be closed off
using the caps supplied.
The following procedures must be carried out
before installing the appliance:
*A proper wiring system must be installed.
*If your appliance is to be installed in
Discharging mode, the ventilation hole must
first be made and a proper pipe obtained to
connect the vent to the flange of the
extractor hood.
Wall fitting
*Using the appropriate drilling jig, insert the
blocks supplied into the wall. Then insert
two of the screws supplied so that the
appliance can be hooked onto the screws
by the holes specially provided (fig 5A).
*Once the appliance is hooked in place it can
be firmly secured to the wall using the other
two screws and the holes provided
underneath (fig. 5B). To avoid damaging the
appliance only use the holes already
created.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG OWM655 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG OWM655 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info