772601
19
Zoom out
Zoom in
Previous page
1/42
Next page
17
EN
Malfunctions
F1, F8, E1, E2, E7 or E8 appears in the display.
The appliance has suffered a fault. Contact the customer service
department.
The fans inside the appliance are running although the
fan function has been deactivated and the compressor
(refrigeration unit) is idle.
This is a normal operating state depending on the set interior
temperature and ambient temperature at the place of installation.
You may be able to rectify the following faults by checking
the possible causes yourself.
Appliance does not function:
Is the appliance switched on?
Is the plug correctly fitted in the mains socket?
Is the fuse intact?
When inserting the mains plug, the refrigeration unit does
not switch on, but a value is shown in the temperature
display.
Demo mode is activated. Contact the customer service depart-
ment.
Loud running noise:
Is the appliance set up firmly on the floor?
Does the appliance cause nearby items of furniture or objects to
vibrate? Please note that noises caused by the refrigerant circuit
cannot be avoided.
The temperature is not low enough:
Is the temperature setting correct (see "Setting the temperature")?
Does the separately installed thermometer show the correct
reading?
Is the ventilation system working properly?
Is the dust filter in the appliance plinth soiled? See section entitled
"Cleaning the dust filter".
Is the appliance set up too close to a heat source?
If none of the above causes
apply and you cannot rec-
tify the fault yourself, contact
the nearest customer ser-
vice department stating the
type designation 1
, service
number 2and appliance
number 3as indicated on the
type plate.
The position of the type plate is shown in the section entitled
Description of the appliance.
Shutting your appliance down
If your appliance is to be shut down for any length of time, switch
it o and disconnect the plug or switch o or unscrew the fuse.
Clean the appliance and leave the door open in order to prevent
unpleasant smells.
The appliance complies with the relevant safety regulations and
EU Directives 2014/30/EU and 2014/35/EU.
Inserting the wooden shelf
Removing and inserting the wooden shelves
The wooden shelves can be removed for easier cleaning of the
inside of the appliance.
Removing the wooden shelf
Extend the pull-out rails as far as they will go. Place the front
recesses of the wooden shelf on the securing pins.
Slide the wooden shelf together with the pull-out rails into the
appliance as far as they will go.
Push the wooden shelf right to the back so that it clicks into place
at the front.
Push the wooden shelf downwards on the right and left at the
back and click into place.
Pull the wooden shelf upwards on the right and left
at the back (release) and then remove it towards you.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG KU8071K2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG KU8071K2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG KU8071K2

ATAG KU8071K2 User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info