331535

ATAG hi7071a Manual

71
Zoom out
Zoom in
Previous page
1/73
Next page
fitting the connection cable
1. Open the cover of the junction box with a
screwdriver.
2. Fit the connection cable and make the correct
connections using the bridges supplied (see wiring
diagram). Inside the lid of the connector block, you
will find an illustration showing how to make the
connections with the bridges.
3. Fasten the cable with the strain relief and close the
cover.
If you wish to make a fixed connection, the plug
should be fitted with a multipolar isolating switch with
a minimum contact gap of 3 mm.
Use an approved cable for the connection, in
accordance with the regulations. The cable casing
should be of rubber.
installation
building in
GB 31
installation
possibilities for building in
attention
Ensure that the connection cables hang freely. If there
is a drawer underneath the hob, make sure that the
contents do not project above the edge of the drawer
and interfere with the ventilation.
installation of the induction hob above a combi-
microwave oven, a 90 cm ATAG oven or an oven of a
different brand
e
Saw out the ventilation opening(s), making sure
that the total surface of the holes is a minimum
of 100 cm
2
. See the drawing, for example,
showing 2 holes of 50 cm
2
.
r
Fit a protective plate between the oven and the
hob. The plate should be at least 10 mm thick
and heat-resistant (85 °C). The space between
the underside of the hob and the protective plate
must be at least 50 mm.
t
To protect the air flow, fit a protective panel - of
the same material as the protective plate -
between the protective plate and the hob.
Ventilation is via the adjoining cupboards.
GB 30
2
50 cm
e
r
t
e
e
r
t
50
200
52
min.
560 x 6 mm
12345
right zones
left zones
Hob type Induction
Component voltage 230V 50Hz
Appliance width x depth 770 x 510 mm
Built-in height from
top of worktop 48 mm
Cut-out width x depth 750 x 490 mm
Worktop thickness 28 – 50 mm
Capacities of modules
Left 3600 W
Right 3600 W
inside the appliance
… 71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG hi7071a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG hi7071a in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info