336580
73
Zoom out
Zoom in
Previous page
1/86
Next page
GB 31
SYMPTOM
POSSIBLE CAUSE SOLUTION
You have switched a cooking
zone on but the display keeps
ashing.
The pan you are using is not
suitable for induction cooking
or has a diameter of less than
12 cm.
Use a suitable pan
(see page 13 and 14).
A cooking zone suddenly
stops working and you hear a
signal.
The preset time has ended. Switch the bleep off using the
or button on the timer.
The hob is not working and
nothing appears in the display.
There is no power supply due
to a defective cable or a faulty
connection.
Check the fuses or the electric
switch (if there is no plug).
A fuse blows as soon as the
hob is switched on.
The hob has been wrongly
connected.
Check the electrical
connections.
Fault code E6. The hob has been wrongly
connected.
Check the electrical
connections.
Fault code F00. The control panel is dirty or
has water lying on it.
Clean the control panel.
Fault code F0 ... F6 and FC. Defective generator. Contact the service
department.
Fault code F7. The ambient temperature is
not good.
Switch off all heat sources in
the vicinity of the cooking
plate.
Fault code F8 and F08. Appliance over heated. The appliance has been
switched off because of over
heating. Let the appliance
cool down and start again on
a lower setting.
Fault code F9 and/or
continuous beep.
The appliance has been
connected incorrectly and/or
the mains voltage is too high.
Let your connection be
changed.
Fault code F99. You have pressed two or more
buttons at the same time.
Do not operate more than
one button at the same time.
Fault code FA. Mains voltage is too low. Contact your energy supplier.
Fault code FAN. Air circulation not good. Make sure the venting holes
under the cooking plate are
open.
Other fault codes. Defective generator. Contact the service
department.
General
TROUBLESHOOTING
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG hi 6271 f at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG hi 6271 f in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG hi 6271 f

ATAG hi 6271 f Installation Guide - English, German - 2 pages

ATAG hi 6271 f User Manual - German - 90 pages

ATAG hi 6271 f Installation Guide - Dutch, Danish, French - 2 pages

ATAG hi 6271 f User Manual - French - 90 pages

ATAG hi 6271 f Installation Guide - Swedish, Norwegian - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info