556868
6
Zoom out
Zoom in
Previous page
1/94
Next page
6
2
Converting (see illustration B)
The position, the burner type (upper case character) and the tap (lower case character) are schematically indicated
on the sticker in the bottom layer. There are small bags with the corresponding characters in the conversion set
(see “Introduction”).
1. Replace the injectors in the burners. Use a tubular spanner 7 for disassembling/assembling the injector
(see illustrations B1, B2 en B3).
2. Replace the simmer setting screws in the taps. The position of the simmer setting screw can vary per type of
gas tap (see illustration B4). Use a screwdriver, blade width 4 mm, for disassembling/assembling of the simmer
setting screw (see illustration B5/B6) and when necessary use pliers.
3. On the wok burner, replace the injectors for simmer (G1), wok (G2) and roast (G3). The wok injector is
indicated by one rib on the injector holder, the roast injector by two ribs. The simmer injector is the one in the
middle (see illustrations B7 and B8). You can replace the simmer injector with a no. 7 open-end spanner and
a 3.6 Nm tightening moment. Use a no. 10 open-end spanner with a 5 Nm tightening moment to replace the
roast and wok injectors.
For verifi cation, you can fi nd the values of the injectors and simmer setting screws on the data label of this
se
t! For verifi cation also view the values table, injector and simmer setting screws.
4. Place the sticker ‘H1’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) in the bottom tray (see illustrations B9, B10 and B11).
5. Place the sticker ‘H2’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) on the underside of the bottom tray (see illustrations B9, B12 and B13).
6. Place the sticker ‘G2’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) on the back of the user manual (see illustrations B9, B14 and B15).
Warning!
Check the appliance for gas tightness, especially the injectors and simmer setting screws!
Always check for gas tightness before using the appliance! Check the other injectors fi rst before checking
the roast injectors.
Please note: to do this, connect the appliance to the mains.
Do not forget to use the insulation plate!
B1
B2
B3
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG HG9571MDA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG HG9571MDA in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG HG9571MDA

ATAG HG9571MDA Installation Guide - English - 2 pages

ATAG HG9571MDA User Manual - English - 34 pages

ATAG HG9571MDA Installation Guide - German - 2 pages

ATAG HG9571MDA User Manual - German - 34 pages

ATAG HG9571MDA Installation Guide - Dutch - 2 pages

ATAG HG9571MDA User Manual - Dutch - 34 pages

ATAG HG9571MDA Installation Guide - Danish, French - 2 pages

ATAG HG9571MDA User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info