336573

ATAG hg 9611 sba Manual

50
Zoom out
Zoom in
Previous page
1/58
Next page
99
ENVIRONMENTAL ASPECTS
disposal of packaging and appliance
In the manufacturing of this appliance use has been made of durable
materials.
The appliance packaging is recyclable. The following may have been
used:
• cardboard;
• paper;
• polythene film (PE);
• CFC-free polystyrene (PS hard foam);
• polypropylene tape (PP).
Dispose of these materials in a responsible manner and in accordance
with government regulations.
On the data plate is put the symbol of a crossed-out wheeled dustbin:
This means that at the end of its working life, the product must not be
disposed of as urban waste. It must be taken to a special local authority
differentiated waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources.
As a reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
If the appliance does not work properly, this does not always mean
that it is defective. Try to deal with the problem yourself first by
checking the points mentioned below:
fault
There is a smell of gas in the vicinity
of the appliance.
A burner does not ignite.
The burner does not burn evenly.
The burner goes out after igniting.
cause
– A burner is turned on but not lit.
– The coupling on a bottled gas unit
has come undone.
– Plug not in socket.
– Fuse defective/fuse in meter
cabinet switched off.
– Sparkplug dirty/damp.
– Burner parts not correctly installed.
– Burner parts dirty/damp.
– Main gas tap closed.
– Fault in the gas network.
– Gas bottle or tank is empty.
– Wrong type of gas used (where
bottled gas is used).
– Control knob not kept pressed in
long enough or far enough.
– Burner parts incorrectly installed.
– Burner parts dirty or damp.
– Wrong type of gas used (where
bottled gas is used).
– Control knob not kept pressed in
long enough (appliances with
flame failure device).
solution
– Close the tap and wait for a few
minutes before relighting.
– Tighten the coupling.
– Push the plug into the socket.
– Fit a new fuse or switch the
automatic fuse back on.
– Clean and dry the sparkplug.
– Assemble the burner parts using
the centring ridges.
– Clean and dry the burner parts,
making sure that the outflow holes
are open.
– Open the main gas tap.
– Check with your gas supplier.
– Connect a new gas bottle or have
the tank filled.
– Check that the gas used is suitable
for the appliance.
– Keep the control knob pressed in
far enough between full and low.
– Assemble the burner parts using
the centring ridges.
– Clean and dry the burner parts,
making sure that the outflow holes
are open.
– Check that the gas used is suitable
for the appliance.
– Keep the control knob pressed in
for at least 5 seconds.
98
FAULTS
table
In case of faults phone the service department. See the guarantee
certificate or consult the internet site www.hps.nl.
This appliance should only be connected up by a registered installer!
700001740000_hl_HG_4t:opm 23-10-2007 9:59 Page 98
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG hg 9611 sba at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG hg 9611 sba in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info