74656

ATAG FG 1093 K Manual

14
Zoom out
Zoom in
Previous page
1/32
Next page
14
For the userGB
HOW TO USE THE ROTISSERIE
- impale the meat to be cooked on the spit and fix it in the centre
using the two forks provided;
- insert the tip of the spit into the rotation hub on the frame (see
fig. 6);
- unscrew the handle from the spit;
- place the spit support frame in the central runner of the oven,
at the same time inserting the rotation shaft into the motor hub
(see fig. 6);
- place the drip tray on the bottom runner of the oven and pour
a little water into it;
- switch on the heating element;
- close the door gently;
- baste the meat from time to time. When it is cooked, remove
the frame from the motor hub and screw the handle back on to
the spit.
OVENS WITH THERMOSTAT
If cooking temperatures are not as set, call in an engineer to
check the thermostat.
USE OF SINGLE-CONTROL END OF COOKING TIMER (WITH-
OUT CLOCK) (fig. 8)
This allows the cooking time to be programmed.
Operation:
- Move the knob to the desired cooking time (120 mins max.).
- Choose the temperature using the thermostat knob and move
the selector knob to the required cooking method.
- When the programming knob is at the 0 position the oven will
switch itself off. This is automatic.
- Move the thermostat knob back to symbol .
- Move the selector knob to symbol 0.
N.B. If the timer is not used, the oven programming knob is to
be set to the manual position .
USE OF THE ELECTRONIC TIMER (fig. 9)
This allows the start time and cooking duration time to be pro-
grammed.
If food does not need to be watched, this timer can be selected
even when the user is absent. Soon after installation and at any
electrical supply cut-outs the display flashes; the clock must
then be synchronized again to allow programming.
SETTING THE TIMER TO THE CURRENT TIME
- The current time is set by pressing the 2 buttons (COOKING
TIME
and STOP) and the "+" or "-" button at the same time. Any
previous programmes are cancelled and the AUTO symbol
flashes.
NOTE: when the AUTO symbol is flashing the oven cannot be
used manually.
"+" AND "-" BUTTONS
- Pressing the "+" or "- "buttons makes time go up or down at
variable speed according to how long the button is pressed
for.
MANUAL USE
- Press the button: the AUTO symbol goes out (if flashing or
permanently on) the
symbol lights up and the oven can be
used by adjusting the thermostat knob and the selector switch
according to the instructions given in the manual.
AUTOMATIC OPERATION WITH END OF COOKING AND
DURATION TIMERS
- Let’s use an example: it is 9:25 am; you want the oven to switch
on at 11 am and switch off at 12 pm (cooking time 1 hour).
- Press the COOKING DURATION button and within 5 seconds press
"+" button until it shows 01.00, adjust using "-" button if neces-
sary. The
AUTO and symbols come on permanently.
- Press the END OF COOKING button and within 5 seconds press
"+" button until it shows 12.00. The
symbol goes out but the
AUTO symbol remains permanently on.
- Move the oven thermostat knob to the desired temperature,
and the selector switch to the required cooking method; the
red warning light comes on the oven light comes on and the
timer is ready to start: at 11am the oven will come on auto-
matically and the
symbol will light up.
- When cooking is over (12 am) the
AUTO symbol flashes, the
symbol goes out and a buzzer sounds; to turn off the buzzer
press any button.
- Move the thermostat and selector knob to the OFF position.
SEMI-AUTOMATIC OPERATION WITH COOKING DURATION
SELECTION
- Let’s take an example: it is 11:35 am and you want the oven to
stay on for 25 minutes from now on.
- Press the COOKING DURATION button and within 5 seconds press
the "+" button until it shows 00.25, adjusting the time with the
"-" button if necessary. The AUTO and symbols light up
permanently.
- Turn the oven thermostat knob to the desired temperature and
the selector switch to the required cooking method; the red
warning light comes on, the oven light comes on and the oven
starts to operate.
- After 25 minutes the oven and the
symbol go out. The AUTO
symbol flashes and the buzzer tells you that cooking is over:
to turn off the buzzer press any button.
- Then move the oven thermostat knob and the selector switch
to the OFF position.
MINUTE MINDER
- Press the MINUTE MINDER button and choose the desired time
using the "+" or "-" button.
- The BELL symbol lights up when the minute minder is in use.
- When the pre-set time is over, the buzzer sounds and the
BELL symbol goes out.
BUZZER
- The buzzer sounds at the end of a programme and lasts for a
maximum of 7 minutes.
- To turn it off, press any button.
- Pressing the "-" button without having previously selected a
function the frequency of the signal changes. A selection from
3 possibilities can be made. The selected signal is audible as
long as the "-" button is pressed.
STARTING AND CHECKING A PROGRAMME
- The programme starts after about 4 seconds of it being set.
- The set programme can be checked at any point by pushing
the corresponding buttons.
PROGRAMMING ERRORS
- Example: at 12:15 pm a COOKING DURATION time of 30 minutes
is set and a END OF COOKING is programmed in at 12:30 pm.
- The programme error can be rectified by changing the dura-
tion or the end of cooking time, or by pressing the MANUAL
button and programming again.
- If there is a programming error the oven will not come on.
ANNULLING A PROGRAMME
- A programme can be cancelled by pressing the COOKING DU-
RATION
button and then the "-" button until the display shows
0.00.
IMPORTANT:
AT THE END OF EVERY PROGRAMMED COOKING OPERA-
TION YOU ARE ADVISED TO PRESS THE
BUTTON, OTH-
ERWISE THE OVEN CANNOT BE OPERATED MANUALLY.
GENERAL PRECAUTIONS
- Always disconnect the power supply before any work inside
the oven or where live parts may be accessed.
- Never use the warming compartment for storing inflammable
liquids or items which do not withstand heat, such as wood,
paper, aerosol cans, matches, etc.
- Make frequent checks on the rubber connection hose, ensur-
ing that it is well away from hot surfaces, that there are no
sharp bends or kinks, and that it is in good condition. The
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG FG 1093 K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG FG 1093 K in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info