Manual ATAG ES 9011 EM (page 13 of 15) (English, German, Dutch, French)

109596

Zoom out

Zoom in

1/15

- 13 -

GENERAL

Carefully read the following important information regard-

ing installation safety and maintenance. Keep this infor-

mation booklet accessible for further consultations.

The appliance has been designed for use in the ducting

version (air exhaust to the outside – Fig.1B), filtering

version (air circulation on the inside – Fig.1A) .

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simulta-

neously with an open fireplace or burner that depend on

the air in the environment and are supplied by other than

electrical energy, as the cooker hood removes the air

from the environment which a burner or fireplace need for

combustion. The negative pressure in the environment

must not exceed 4Pa (4x10-5 bar). Provide adequate

ventilation in the environment for a safe operation of the

cooker hood.

Follow the local laws applicable for external air evacua-

tion.

Before connecting the model to the electricity net-

work:

- control the data plate (positioned inside the appliance)

to ascertain that the voltage and power correspond to

the network and the socket is suitable. If in doubt ask a

qualified electrician.

- If the power supply cable is damaged, it must be replaced

with another cable or a special assembly, which may be

obtained direct from the manufacturer or from the Technical

Assistance Centre.

2. WARNING !

In certain circumstances electrical appliances may be

a danger hazard.

A) Do not check the status of the filters while the

cooker hood is operating

B) Do not touch bulbs or adjacent areas, during or

straight after prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker

hood

D) Avoid free flame, as it is damaging for the filters

and a fire hazard

E) Constantly check food frying to avoid that the over-

heated oil may become a fire hazard

F) Disconnect the electrical plug prior to any mainte-

nance.

G) This appliance is not intended for use by young

children or infirm persons without supervision

H) Young children should be supervised to ensure they

do not play with the appliance

I) There shall be adequate ventilation of the room

when the rangehood is used at the same time as appli-

ances burning gas or other fuels

L) There is a risk of fire if cleaning is not carried out

in accordance with the instructions

This appliance conforms to the European Directive EC/

2002/96, Waste Electrical and Electronic Equipment

(WEEE). By making sure that this appliance is disposed

of in a suitable manner, the user is helping to prevent

potential damage to the environment or to public health.

The

symbol on the product or on the accompanying

paperwork indicates that the appliance should not be

treated as domestic waste, but should be delivered to a

suitable electric and electronic appliance recycling

collection point. Follow local guidelines when disposing

of waste. For more information on the treatment, re-use

and recycling of this product, please contact your local

authority, domestic waste collection service or the shop

where the appliance was purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried

out by specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II,

therefore no earth cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load

indicated on the description label. Where a plug is pro-

vided, the cooker hood must be installed in order that the

plug is easily accessible.

An omnipolar switch with a minimum opening of 3mm

between contacts, in line with the electrical load and

local standards, must be placed between the appliance

and the network in the case of direct connection to the

electrical network.

• The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm.

If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same

conductor used to circulate hot air or for evacuating

fumes from other appliances generated by other than an

electrical source.

Before proceeding with the assembly operations, remove

the anti-grease filter(s) (Fig.16) so that the unit is easier

to handle.

In the case of assembly of the appliance in the suction

version prepare the hole for evacuation of the air.

• Hood assembly

Remove the structure from the packaging and remove

the 2 screws A to separate the upper part from the lower

part (fig.2).

- Position hole template on the ceiling paying attention

that the arrow is positioned on the same side as the

appliance controls (Fig.3).

Make 4, Ø8 holes in the ceiling and drive in 3 screws

without completely tightening them. Pay attention not to

insert the screw into the hole marked with an X on the

hole template (the screws and expansion plugs must be

suitable for the type of wall).

- Take the upper part of the structure B (fig.4) and insert

the 3 slots onto the 3 screws that are not completely

tightened.

Rotate slightly to fit (fig.4) .

Drive in the fourth screw X and tighten the remaining 3 to

allow definitive blocking of the upper part of structure B

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ES 9011 EM in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATAG ES 9011 EM Manual

Product: