108522
15
Zoom out
Zoom in
Previous page
1/38
Next page
GB 7
solution
Change the light bulb.
- Gently press the front side of
the window (1) and it should
tilt open slightly (2).
- Open the window fully and
fit a new 20 W halogen bulb.
Note: do not touch the bulb’s
glass with your fingers.
- Gently push the window
closed again.
Change the discharge duct
(see installation instructions).
Phone the Service department.
Phone the Service department.
Phone the Service department.
cause
Lamp defective.
NB:
Only use the same type of lamp
with the wattage stated.
Discharge duct too long or has
too many bends.
Motor defective.
Motor or controls defective.
Connection lead defective.
fault
Lighting does not work.
Extractor hood makes a lot of
noise.
No extraction.
faults
Please check the following points which may solve the problem, before calling the service
department.
If the connection cable is damaged, it should be replaced by the service department of the
manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.
NB: Disconnect the appliance from the mains before starting any repairs, preferably by removing
the plug from the socket or by setting the isolation switch to zero.
GB 6
carbon filter indicator (optional)
switching on the carbon filter indicator
If you use the recirculation extractor hood, you must use a
carbon filter. In that case, you can switch on the carbon
filter indicator. Press keys
OFF
and
ON
for approx. 5
seconds in order to switch on the carbon filter indicator.
The 4 green LEDs light up and the extractor hood gives an
audible signal.
replacing the carbon filter
If the 2
nd
red LED in the control panel starts to flash, clean
the filter immediately. Place a new carbon filter and erase
the electronic memory by pressing the
ON
button for
approx. 5 seconds. The 2
nd
red LED stops flashing.
switching off the carbon filter indicator
Press keys
OFF
and
12h
for approx 5 seconds in order to
switch off the carbon filter indicator. The 4 green LEDs light
up and the extractor hood gives an audible signal.
You can check if the carbon filter is switched on by pressing
the keys
and
12h
continuously for approx 5
seconds. When the carbon filter indicator is switched on the
4 green LEDs light up, otherwise the 4 red.
As you press a key, a key signal sounds in confirmation.
Press keys
ON
en
12h
for 3 seconds continuously on
the in order to switch on the key signal.
Repeat this procedure if you wish to switch off the key
signal again.
OFF ON 12h
switch off the key signal
1
2
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG ES 1292 MM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG ES 1292 MM in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG ES 1292 MM

ATAG ES 1292 MM User Manual - English, German, Dutch, French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info