467230
12
Zoom out
Zoom in
Previous page
1/16
Next page
O p e r a t i n g I n s t r u c t i o n s
8G.52.6000/03.07 Changes reserved
Boiler G.C No
E22S 41-310-12
E32S 41-310-13
E22C 47-310-13
E32C 47-310-14
CE PIN 0063BR3405
Operating instructions ATAG E-Series
2
Content
Introduction ...................................................... 3
Safety ............................................................... 4
Description of the boiler.................................... 5
Explanation of the function keys and display.... 7
The Reset key .................................................. 7
The boiler display .............................................. 8
Water pressure in the central heating system ... 9
Replenishing the central heating...................... 10
Turning the boiler off ........................................ 12
Error codes, Maintenance and Warranty ......... 13
Adjustments.................................................... 14
Important!
It is in your own interest that we should know that you have an ATAG
boiler. Please fill out the warranty card completely and send it back to
us. Then we can be fully at your service.
Operating instructions ATAG E-Series
3
These operating instructions describe the
functioning and the operating of the ATAG E boilers.
This manual is for the end user. For installation and
servicing there is an installation & servicing
instructions manual for the installer.
Read this manual fully before operating the boiler. In
case of doubt or errors contact your installer.
ATAG Heating reserves the right to change the
specifications and dimensions without prior notice.
Work on the boiler must be carried out by a
competent person, (Ref: Gas Safety Installation
and Use ) using correctly calibrated instruments
with current test certification.
When replacing parts use only ATAG Service parts.
Introduction
Operating instructions ATAG E-Series
4
In case you smell gas:
- No naked flames! Do not smoke!
- Do not operate electrical switches for lights or
any other appliance.
- Do not use a telephone
- Turn off gas supply at meter
- Open windows and doors
- Notify any persons in the building and leave the
building at once.
- Call Gas company or installer only when
outside the building
Protection from corrosion
Do not use any sprays, chlorine containing agents,
solvents, paint etc. around the boiler or around the
air intake supply entrance of the boiler. These
substances have negative influences on the boiler
and can lead to corrosion resulting in failure of the
boiler.
Checking the water pressure
Check the water pressure in the central heating
installation regularly.
Use only potable water for filling.
Use additives only after clearance by ATAG.
Contact your installer if in any doubt.
Safety
Operating instructions ATAG E-Series
5
The ATAG E boiler is a room sealed, condensing
and modulating central heating boiler, with or
without an integrated hot water facility.
The boiler is provided with a compact stainless
steel heat exchanger with smooth tubes. A well
thought out principal using durable materials.
The boiler burns gas for supplying warmth. The
heat is transferred in the heat exchanger to the
water in the central heating system. By cooling
down the flue gasses condensate is formed. This
results in high efficiency. The condensate, which
has no effect on the heat exchanger and the
function of the boiler, is drained through an internal
siphon.
The boiler is provided with an intelligent control
system (CMS Control Management System). The
boiler anticipates the heat demand of the central
heating system or the hot water facility.
When an outside sensor is connected to the boiler,
the boiler works weather dependantly. This means
that the boiler control measures the outside
temperature and flow temperature. With this data
the boiler calculates the optimal flow temperature
for the installation.
Room sealed boiler
The boiler retreives its
combustion air from outside
then discharges the flue
gasses to the outside.
Condensing
Retrieves heat from the
flue gasses. Water
condensates on the heat
exchanger.
Modulating
Higher or lower burning
according to the heat
demand.
Stainless Steel
Super solid kind of steel
which keeps its quality for
life. It will not rust or erode in
contrast to composition
materials, like aluminium.
Description of the boiler
Operating instructions ATAG E-Series
6
The efficiency of the boiler is very high and the
radiation convection and standby losses very low.
The emission of noxious substances is far below
the fixed standards so the boiler is SEDBUK Class
A rated.
When the boiler is connected to an ATAG BrainQ or
Smart a lot of information can be retrieved from the
boiler. For more information about the ATAG
thermostats. Please refer to the user manuals.
On the left side of the boiler there is a small door.
Through the transparent part you can see the
boiler status on the display. After opening this door
you will find the function keys. On the left side of the
function keys you will find instructions of the display
messages and function keys. These are also
described in the following pages.
ATAG BrainQ
ATAG Smart
Example SEDBUK ClassA
Operating instructions ATAG E-Series
7
On/off key Central heating.
When 'on' the indication L.E.D. is illuminated.
On/off key Domestic hot water (DHW)
When 'on' the indication L.E.D. is illuminated.
On/of key Pump programm. Continuously yes/no
When 'on' the indication L.E.D. is illuminated.
In most situations the pump can stay in position 'off'.
During severe frost it is possible (when there is no outside
sensor connected), to choose manually to let the circulation
pump circulate continually thus reducing the chance of freezing
pipes (garage, attic or other cold spaces / rooms) which are
sensitive to frost.
Explanation of the function keys and display
The control panel is provided with a reset key.
When a fault occurs it will be shown by the flashing
E (Error) with a number code after which the boiler
is shut down. After pressing the reset key you can
try to start the boiler again. If the error message
keeps occurring contact your installer.
The Reset key
When the pump is switched
on continuously it can lead
to undesired heating up of
the central heating system
during the summer.
Central heating
on/off
Domestic Hot water
on/off
Pump program
on/off
Reset key
Unlocking the boiler
Display
Mode key
Selecting chapters
Step key
Scrolling
Indication L.E.D.'s
+
-
Operating instructions ATAG E-Series
8
The boiler display
The boiler display can be set to read in two ways:
The Good reading
During this reading the display will only show what
is necessary. Under normal circumstances the
display will give a Good reading. If a fault is
detected the boiler will be blocked. This will be
shown with, alternate display of Good, with an E
of Error or a BL of Blocking and a number code. For
further information refer to page 13 "Errors,
maintenance and warranty" .
The technical reading
During this reading the display will show in which
operating status the boiler is active. The technical
reading is shown alternately with the water
pressure. The first figure in the technical reading
indicates the status in which the boiler is active and
the third and fourth figure indicate the water
temperature of the boiler. For example in the
reading P 1.9 the character P stands for pressure
which represents the water pressure. The third and
fourth figure indicate the water pressure in bar.
If a fault is found, the same is shown as described
under "The Good reading".
Selecting the Technical or Good reading.
- Press the Step key for 5 seconds.
The display will change from the Good reading to the
technical reading or vice versa.
Operating instructions ATAG E-Series
9
Water pressure in the central heating system
The installation will function optimally with a water
pressure of between 1,5 and 1,7 bar.
If the water pressure drops below 1 bar, the display
will show FILL. During this message the boiler will
remain functioning at a reduced level. After
replenishing the system to just above 1,5 bar the
message FILL will disappear and the boiler will
function normally again.
When the water pressure drops below 0,7 bar, the
display will show a flashing FILL text.
The boiler will shut down and will function normally
again only after replenishing the system to just
above 1,5 bar.
To retreive the water pressure on the display from
the Good reading:
- Press the Step key once briefly.
The water pressure will be shown.
Press the Step key briefly to return to the Good
reading.
Message ' Water pressure
too low' on your ATAG
thermostat.
On the display of the ATAG
Brain Q as well as the
ATAG Smart a low water
pressure can be indicated.
For further information see
the relevant user manual.
Operating instructions ATAG E-Series
10
Replenishing the central heating system
The central heating installation needs to be filled with potable (drinking) water.
For topping up the installation you use the filling loop according to the following
procedure:
(If in any doubt please contact your dealer)
1 Switch all functions off (heating, DHW and pump);
2 Briefly push the 'STEP'-button: P x.x = water pressure in bar;
3 Slowly open the filling loop (Indication on display increases);
4 Fill up slowly to 1.5 to 1.7 bar;
5 STOP appears on the display;
6 Close the filling loop;
7 De-aerate the complete installation, start at the lowest point;
8 Check the water pressure and if necessary top it up;
9 Close the filling loop;
10 Activate functions required (heating , DHW and/or pump );
11 If A xx appears on the display, wait for 17 minutes.
Do not press any further keys or the deaeration period will start again;
12 Check the waterpressure and if necessary top it up to 1,5 to 1,7 bar;
13 Close the filling loop;
14 Press the ‘STEP’-button;
15 Be sure that the filling loop is closed.
After the automatic de-aeration program (A xx) is finished the boiler will return
to the Good reading or Technical reading.
Operating instructions ATAG E-Series
11
The boiler will not function directly. The automatic de-aeration programme
of about 17 minutes will start after one of the three program keys is pressed.
The display will show where A stand s for Automatic de-aeration
programme Active and the number on the right indicates the actual water
temperature of the boiler.
Check the water pressure regularly and top up the installation when necessary.
The working pressure of the installation should be between 1.5 and 1.7 bar
It can take a while before all air has dis-appeared from a filled installation. Especially
in the first week noises can be heard which indicate the presence of air. The
automatic air vent in the boiler will make this air disappear, which means the water
pressure will reduce during this period and therefore topping up with water will be
necessary to adjust the flow water temperature
Operating instructions ATAG E-Series
12
Holiday period:
Adjust the thermostat to the holiday period. See
the user thermostat manual. The hot water facility
can be switched off by means of the program key
on the control panel.
Re-setting the central heating system:
Switch off the three program keys , , if
these are activated.Switch off the power supply.
When the boiler is being drained one should take
into account that a part of the heating water will
remain in the boiler. When risk of frost arises one
should take care that the remaining central heating
water in the boiler does not freeze.
Holiday
The ATAG BrainQ room
thermostat is provided with
a holiday program. The
holiday period can be
adjusted on the thermostat
itself. The central heating
and DHW supply are
switched off during that
period. There is also the
option that only the central
heating is switched off. With
all of these possibilities the
frost protection system is
active.
Turning the boiler off
Operating instructions ATAG E-Series
13
Error, maintenance and warranty
If a fault is detected the boiler will be blocked. This
will be reflected, by an alternate display of Good,
with an E for Error or a BL for Blocking and a number
code.
You can try to reset the boiler by pressing the
Reset key once. If the problem remains please
contact your installer and inform them about the
fault and give them the number code.
If you discover any leaks from the boiler contact
your installer.
We advise you to obtain a service contract with
your installer for regular maintance and
adjustment to keep your boiler safe and in good
condition.
The casing of the boiler consists of metal and
plastic parts which can be cleaned with a normal
non abrasive cleaning agent.
You can find the warranty conditions in the
warranty card which is supplied with the boiler.
Operating instructions ATAG E-Series
14
Adjustments
The boiler has a large number of settings options.
We advise you to contact your installer for
adjusting the boiler to your required settings.
Adjusting the flow water temperature (CH)
- Press the Mode key briefly
(from the Technical reading).
The display will show PARA .
- Press the Step key once.
The display will show 1 85 .
- Press the + or the - key to alter the adjustments,
if necessary.
- Press the Store key to confirm the setting.
The display will flash once.
- Press the Mode key briefly.
The display will show StbY for a short while and
will return to the Technical reading.
The flow water temperature that has been adjusted
only applies to the central heating and is independent of the hot water facility.
Operating instructions ATAG E-Series
15
Selection Type of installation
Flow water
temperature
01
Radiators; air heating; convectors 85°C
02
Radiators with large surface areas or under floor heating as
additional heating
70°C
03
Under floor heating with radiators as additional heating 60°C
04
full under floor heating 50°C
= factory setting
Adjusting the type of installation
The boiler is designed in such a way that it will adjust
itself automatically to what is necessary for a
normal heating system. In some cases the
installation may have convectors or complete
underfloor heating.
One can easily choose heating installation
adjustments appropriate for the system such as
maximum water-flow temperature or for the
warming up of the installation after a night period.
Adjustment goes as follows:
- Press (from the Technical) reading the Mode
key once;
- Press the Step key twice;
The display will show 2 01.
- Press the + or the - key to alter the type of
installation according to the table below;
- Press the Store key to confirm the setting;
The display will flash once.
- Press the Mode key once;
The display will show StbY for a short while and
will return to the Technical reading.
When a type of installation has been chosen with a low water-flow temperature
it is possible that in case of a severe winter period the temperature of the
heating system will need to be increased slightly. In such situations the
installation choice may need to be changed, so that a higher flow temperature
can be chosen. This adjustment would normally be carried out by your installer
during the installation and commissioning.
+
Store
Mode
Step
Reset
-
Details of your installer:
Name of installer:
Address:
Contact:
Phone number:
Phone number outside business hours:
Ditributor for UK
ATAG Heating UK Ltd. • Unit 3 • Beaver Trade Park • Quarry Lane Chichester
West Sussex PO19 8NY • Phone: 01243 815 770 • Fax 01243 839 596
E-mail: info@atagheating.co.uk • Internet: www.atagheating.co.uk
Ditributor for Ireland
Total Energy Management Ltd. • Unit 9 • Ballybritt Industrial Estate • Monivea
Road Galway Ireland • Phone: 091 769174 • Fax 091 769485
E-mail: info@tem.ie • Internet: www.tem.ie
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG E223C-CW3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG E223C-CW3 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG E223C-CW3

ATAG E223C-CW3 Manual - Dutch - 2 pages

ATAG E223C-CW3 Installation Guide - Dutch - 44 pages

ATAG E223C-CW3 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info