111712

ATAG CM 4192 AC Manual

73
Zoom out
Zoom in
Previous page
1/93
Next page
YOUR COFFEE MACHINE
9 Installation instructions
GB 35
9.1 Important matters
After removing the packaging, make sure the product is complete •
and undamaged. If in doubt, do not use the appliance and contact
a qualifi ed professional.
Installation must be carried out by a qualifi ed techncian and in •
compliance with current regulations.
Packing elements (plastic bags, polystyrene etc.) must not be left •
within reach of children as they may represent a hazard.
Never install the appliance in environments where the •
temperature may reach 0 °C or lower (the appliance may be
damaged if the water freezes).
Make sure the mains voltage corresponds to the voltage indicated •
on the appliance rating plate. Connect the appliance to an
effi ciently earthed socket with a minimum current rating of 10A
only.  e manufacturer may not be considered liable for possible
incidents caused by the failure to adequately earth the mains.
If the power socket does not match the plug on the appliance, •
have the socket replaced with a suitable type by a qualifi ed
professional.
e power socket has to remain visible after installation. •
Do not use multiple plug adapters or extension leads. •
e power cable on this appliance must not be replaced by the •
user as this operation requires the use of special tools. If the cable
is damaged or requires replacing, contact an authorised service
centre only to avoid all risks.
For the electrical connection use a HO5 VV-F type cable as •
indicated in the table below:
Conductors Amount x size
230 V ~+ ~ 3 x 1.0 mm
2
You should personalise water hardness as soon as possible •
following the instructions in 6.2.2 on page 24 and 25.
YOUR COFFEE MACHINE
8 Faults
GB 34
PROBLEM CAUSE SOLUTION
Ground coff ee was used
(instead of coff ee beans)
and the machine will not
dispense any coff ee.
e “coff ee strength/
preground coff ee” knob is
not turned completely to
the left
or right
and the appliance used
both preground coff ee and
coff ee ground by the mill
mechanism.
Preground coff ee was inserted
whilst the machine was
switched off .
Carefully clean the inside of
the machine (see page 12).
Repeat the process, but fi rst
turn the “coff ee strength/
preground coff ee” knob
completely to the left
or
right
(see 5.2.5 on
page 14).
Remove the brewing unit and
carefully clean the insided of
the machine (see 6.1.1 and
6.1.2 on page 21, 22 and 23).
Repeat the process with the
machine switched on.
Coff ee does not come out
of the spouts on the coff ee
dispenser but out of the
service door at the side.
e holes on the coff ee
dispenser are blocked with
dried on coff ee.
e swing drawer on the
inside of the service hatch is
blocked and will not move.
Remove the dried on coff ee
with a needle (see 6.1.1 on
page 21, fi g. 24).
Carefully clean the swing
drawer, particulary in the area
around the hinges so that
these continue to move.
Milk is frothed up too much
or too little.
Wrong setting of the slider on
the lid of the milk container.
If the milk is not frothy
enough, the milk container
may not be correctly in place.
You can set the amount of
froth on the milk to any
level using the slider on the
lid (fi g. 19 on page 17):
‘CAPPUCCINO’ (very frothy
milk) or ‘CAFFELATTE’
(not so frothy milk).
Put the milk container
correctly in place. (fi g. 18 on
page 17).
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG CM 4192 AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG CM 4192 AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info