673146

Astralpool OPTIMA 7 Manual

11
Zoom out
Zoom in
Previous page
1/75
Next page
11
ENGLISH
4. START-UP OF THE HEAT PUMP
4.1. Installation rules
It is necessary to determine the unit location according to certain criteria:
The unit must be secured on a hard base (concrete or hard steel frame type) and must be protected from flood
risks
The unit must be installed outside, far away from the sun’s direct rays and any other heat source.
A clear space around the unit of around 1 m at the front and a minimum of 0.5 m at the back and sides of the unit
must be left.
The air caused by the helix must be directed away from the limits of the work environment (windows, doors...).
The minimum distance between the heat pump and the rim of the swimming pool must be, at least, 3.5 m.
(Electrical Regulations for Low Voltage, Supplementary Technical Instructions, Low Voltage, 31, ITC-BT-31).
The electrical and hydraulic connections must be made according to the applicable regulations (NF C 15 100, EC
1364). The ducting for the connections must be fixed.
During operation of the equipment, it is normal that the condensation produced by the evaporation unit will
produce a certain quantity of water which will have to be evacuated.
This condensation water does not have to be treated in any special manner.
Do not install the pump close to place where a big amount of water could reach the machine. Ceilings and water
conduits could forward rain water that mixed with other solid materials could damage the heat pump.
4.2. Hydraulic connections
Connect the PVC piping water inlets and outlets of the swimming pool to the heat pump inlet and outlet. The
connection will be performed through a by-pass over the filtering circuit of the swimming pool after the filter and
before the water treatment. .
Set the by-pass until the pressure switch be between 200 PSI – 300 PSI.
Always follow the installation diagram showed above. Chemical doser must be installed 25 cm under the heating
pump. If not possible contact the installer.
The unit is provided with three PVC unions.
Always respect the hydraulic connection diameters specified for each machine.
A full-flow shut-off valve should be installed on each of the hydraulic elements in the equipment, so that each of
these may be isolated if needed (for repairs, substitutions, etc.) without the need to drain the circuit.
Anti-vibration dampers should be installed in the inlet and outlet of the machine, in order to avoid vibrations which
may cause cracks or breakage in the hydraulic connections.
In order to avoid possible breakage, do not force the PVC tubes connected to the water supply.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Astralpool OPTIMA 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Astralpool OPTIMA 7 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info