628507
100
Zoom out
Zoom in
Previous page
1/112
Next page
EF1210 U
SER
M
ANUAL
A-8 http://www.aspi.com Copyright © 1999, All Rights Reserved
The default choice is pink noise played in both Zone A and Zone B.
Choose “No noise generated” for no pink noise in Zone A and Zone B.
Choose “Pink noise to Zone A” for pink noise in Zone A.
Choose “Pink noise to Zone B” for pink noise in Zone B.
ii. Select input channel to calibrate.
iii. You will need a Sound Level Meter (SPL Meter) for this step. Adjust micro-
phone and loudspeaker to attain the appropriate dB SPL at the microphone using
the following steps:
Set the SPL meter to C weighted, slow response. Choose the appropriate dB
SPL range using Table 7 below based on microphone type and the talker’s
distance from the microphone.
Place the SPL meter beside the microphone. Point the SPL meter and the
microphone toward the loudspeaker.
Adjust the microphone/loudspeaker so that a nominal dB SPL level based on
Table 7 is registered at the microphone.
iv. Adjust level until the first yellow LED (0 dB) on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
of the EF1210 front panel is lit.
v. Repeat for each input channel or click the Apply Gain to All button to
apply the Input Gain to all input channels. Return all microphones to their nor-
mal operating location and orientation.
vi. After all input channels have been calibrated, press the Next button at the bot-
Table 7: Typical distance from microphone to talker and appropriate dB SPL level.
M
ICROPHONE
T
YPE
T
YPICAL
D
ISTANCE
FROM
T
ALKER
(
FT
.)
SPL L
EVEL
(dB)
Lavalier 6 inches to 1 foot 89 dB SPL
Gooseneck 1-2 feet 77 dB SPL
Boundary or other tabletop 2-3 feet 73 dB SPL
Ceiling 4 or more feet 69 dB SPL
Note.
Always double check the microphone level with normal speech
once the microphones are in normal operating position. Actual
speech levels may vary depending on room reverberation, etc.
Verify that you set a reasonable level (three green LEDs and one
solid yellow LED, or 0 dB) by actually talking and looking at the
meter.
Note.
It is vital to move the SPL meter and/or microphones so that each
microphone sees the correct dB SPL acoustic level as you are cal-
ibrating. Do not assume that because the first microphone sees
the dB SPL level, all other microphones will see the same level
(unless they are moved to occupy the same location as the first).
Note.
Use caution if the microphones lie in two acoustically separated
zones and you are only calibrating one zone. As you cycle through
microphones that lie in the other zone, no activity will be indicated
on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
on the EF1210 front panel.
100


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aspi EF1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aspi EF1210 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aspi EF1210

Aspi EF1210 Additional guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info