628507
38
Zoom out
Zoom in
Previous page
1/112
Next page
EF1210 U
SER
M
ANUAL
36 http://www.aspi.com Copyright © 1999, All Rights Reserved
M
OUNTING
THE
EF1210
The EF1210 can be mounted in a rack enclosure using four large screws (10-32 x 1/
2”) included with the unit. One EF1210 fits in a single rack space.
Recommendation
For Easy Access
While not required, it is prudent to leave a single rack space in between the EF1210
and other units in your rack. This not only is a good design practice, but also gives
you easier access to the backpanel. If you cannot leave a single rack space, mount the
EF1210 below units that are longer in length so that you can access the Phoenix con-
nectors on the backpanel more easily.
Instructions for
Securing Power
Supply to Back of
EF1210
Locate the cable clamp on the back panel of the EF1210 above the RS-232 port.
Remove the screw and thread the power cord through the cable clamp.
Attach the cable clamp to the back panel of the EF1210 and tighten the screw.
Align the clamp so that the power cable does not interfere with the connectors on
the EF1210 backpanel.
Plug in the power supply.
We recommend that you also Ty-wrap the power supply to the rack.
The purpose of securing the power supply to the back panel is so that if the power
supply were to drop, it would pull where the cord is attached with the cable clamp and
not pull the plug out of the EF1210.
Figure 16. Attaching a cable clamp to the back panel of the EF1210
Thread power cable through cable clamp and attach to
EF1210 back panel for strain relief on the power supply.
REMOTE CONTROLREMOTE CONTROL
ASPI BUS IN
ASPI BUS OUT
RS-232
L
INE
L
INE
L
INE
L
INE
L
INE
MIC/L
5, 15 VDC 5, 12 VDC
M
IC
1
P
HANTOM
1
M
IC
2
P
HANTOM
2
D
EVICE
ID 8
D
EVICE
ID 4
D
EVICE
ID 2
D
EVICE
ID 1
21
D
EVICE
ID 16
M
IC
3
P
HANTOM
3
M
IC
4
P
HANTOM
4
M
IC
5-8
P
HANTOM
5
P
HANTOM
6
P
HANTOM
7
P
HANTOM
8
435
R
ESERVED
R
ESERVED
PIN 2: TX
3: RX
ON
15
PIN 2: TXD
3: RXD
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aspi EF1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aspi EF1210 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aspi EF1210

Aspi EF1210 Additional guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info