628507
10
Zoom out
Zoom in
Previous page
1/112
Next page
EF1210 U
SER
M
ANUAL
8 http://www.aspi.com Copyright © 1999, All Rights Reserved
EF1210 C
ALIBRATION
Q
UICK
R
EFERENCE
Calibration Step 1: Calibrating Microphone Input Channels
1.1. Press and hold the AUX IN LEVEL/SETUP and the INPUT SELECT buttons for 2 seconds to enter setup. SETUP LED blinks once
per period.
1.2. Press REF SELECT to select noise output source.
1.3. Press INPUT SELECT to select input channel to calibrate.
1.4. Place SPL meter beside mic pointing in the same direction. Adjust loudspeaker for 73 dB SPL at mic (for boundary mics) or
refer to Table 4 in Calibration Section for other mic types.
1.5. Press LEVEL ADJUST until first yellow LED (0 dB) on INPUT meter is lit on INPUT meter.
1.6. Repeat steps 3-5 for each input channel.
Be sure to move SPL meter or mics so each
mic sees the appropriate SPL level.
2.1. Press the AUX IN LEVEL/SETUP button to enter Zone Output Calibration. SETUP LED blinks twice per period.
2.2. Press REF SELECT to select noise output source (we recommend using both zones simultaneously).
2.3. Select nominal output level for your room audio amplifier with LEVEL ADJUST (press UP for 0 dBu, DOWN for -10dBV).
2.4. Repeat for other Zone output if appropriate. Then return all mics to their operating position and orientation.
2.5. Check acoustic gain limit. Adjust external amplifiers/loudspeakers so that the loudspeaker volume is almost uncomfortably
loud OR no more than 3 green LEDs are lit on INPUT meter.
2.6. Press INPUT SELECT to select next input channel.
2.7. If INPUT meter shows more than 3 green LEDs, turn
down room amplifier.
2.8. Repeat steps 6 & 7 for each input channel.
Calibration Step 2: Calibrating Zone Outputs, Check Acoustic Gain
STEP 1.1
: Press and
hold AUX IN LEVEL/
SETUP button
and
INPUT SELECT for 2
seconds to enter
confi
g
uration mode
STEP 1.3
:
press to select
channel for
calibration
LEDs li
g
ht to
indicate which
channel is selected
LED blinks
once for
microphone
calibration
noise level
measured
at mic
should be
73 dB SPL,
or refer to
Table 4
pink noise to both zones
no noise
g
enerated
pink noise to zone A
pink noise to zone B
STEP 1.5
: adjust
level until 3
g
reen
and 1 yellow LEDs
are lit (repeat for
each channel)
STEP 1.2
: press to
select noise source
-12 -7 -3 0 3 20 dB -12 -7 -3 0 3 20
AUX IN
LEVEL
REF
SELECT
INPUT
SELECT
SETUP
AEC
A
AEC
B
12345678
INPUTPOWER REMOTE
MUTE
ALL
LEVEL
ADJUST
SETUP
AUX IN
LEVEL
REF
SELECT
INPUT
SELECT
SETUP
AEC
A
AEC
B
12345678
INPUTPOWER REMOTE
MUTE
ALL
LEVEL
ADJUST
SETUP
STEP 2.7
: adjust external
amplifiers/loudspeakers so that
no more than 3
g
reen LEDs are
lit (repeat for each channel)
-12 -7 -3 0 3 20 dB -12 -7 -3 0 3 20
STEP 2.2
:
press to select
noise source
noise to both zones (recommended)
noise to zone A
noise to zone B
STEP 2.6
: press
to select channel;
check level
LEDs li
g
ht to
indicate which
channel is selected
LED blinks
twice for Zone
calibration
STEP 2.3a
: press
if amp expects
consumer level
input (-10 dBV)
STEP 2.3b
:
press
if amp
expects 0 dBu
balanced input
LED Off LED On Button
Legend:
LED Blinking
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aspi EF1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aspi EF1210 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aspi EF1210

Aspi EF1210 Additional guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info