309039
27
Zoom out
Zoom in
Previous page
1/36
Next page
Page 9
ENGLISH
ENGLISH
COMMON LACOMMON LAUNDRUNDRY PRY PROBLEMSOBLEMS (CONTINUED) (CONTINUED)
ProblemProblem Possible CausePossible Cause Suggested SolutionSuggested Solution
Empty all pockets and turn inside out before laundering.
Fasten all hooks, snaps, and zippers before laundering to avoid snags.
Remove sharp buckles. Turn knits inside out.
Before washing, rinse harsh chemicals (such as battery acid, hair
care chemicals, cleaning solutions, etc.) from towels and other articles
to avoid holes in fabrics. Do not allow these unrinsed items to contact
other fabrics.
Mend all garments before laundering to prevent enlarging of rips.
These items may fray at edges from normal wear, not the washer.
Wash only in half loads and don’t wash in the same load with heavy
items, such as towels or jeans.
Rips, snags,
excess wear
Sharp objects in pockets
Hooks, snaps, zippers,
buckles
Harsh chemicals
Existing rips and tears
Permanent press items
Permanent press items should be washed in half-loads to prevent
wrinkling. If possible, use a slower spin speed.
Use lower wash temperature settings.
Excessive
wrinkling
Machine too full
Water too hot
ERRERROR MESSAOR MESSAGES – GES – W640/W660W640/W660
Error messages will display in the LED window if faults
occur while a program is in progress. The table below
defines each possible error message.
ERRERROR MESSAOR MESSAGEGE SOLSOLUTIONUTION
When this symbol flashes at the lower right corner of the display it merely means
the glass door isn’t closed securely. Close the door and try again.
0000 If this message flashes at the top right of the LED window, the machine has failed
to spin. This could be because the load is out of balance. Turn the power off
then on again. Open the door and redistribute the washing. Run the Spin
program again.
Door lock fault Call a service technician.
Foaming Run the Rinse program again.
Try using less detergent and softener.
Use low-sudsing detergents. (See page 5.)
Overflow Call a service Technician
Pressure sensor Call a service technician.
Temperature stop Call a service technician.
Thermistor Call a service technician.
Wash motor Call a service technician.
Water inlet Make sure the water tap is open.
Water outlet Check the pin trap for possible blockage. Make sure the outlet hose isn’t kinked.
To remove the message, turn the power off or change
the program.
FFAAULULT CODES – T CODES – W600/W620W600/W620
The Program Control knobs on the W600/W620 have
two fault codes: C and S. If the knob stops on one of
these, the machine detected a problem.
C PositionC Position
This indicates a problem that can probably be taken
care of without calling a service technician. Here are
some possible problems:
Power interruption.
Water not draining out.
Water not filling machine.
The machine didn’t spin.
Refer to the “Troubleshooting” section on the next page
for possible causes and solutions. If none of these
work, call a service technician.
S PositionS Position
If the knob stops on S, this indicates a mechanical
problem and you will probably need to call a service
technician.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Asko w 620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Asko w 620 in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Asko w 620

Asko w 620 User Manual - English - 2 pages

Asko w 620 User Manual - English - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info