76519
31
Zoom out
Zoom in
Previous page
1/36
Next page
31
Positioning the machine
A. Adjusting machines with six feet
(freestanding dishwasher)
1. Adjust the height of the dishwasher with
the four steel feet.
2. Lock the feet with the nuts.
NB! The dishwasher must not be allowed to
lean more than 5 mm.
B. Adjusting machines with three or four
feet
1. Start by measuring the height from the
floor to the underside of the work top of your
kitchen bench.
2. Install the sliding feet on the dishwasher.
3. Measure the height from the floor to the
top edge of the dishwasher.
4. Adjust all the feet by screwing them
clockwise to raise or anti-clockwise to lower.
5. Check that the height of the machine
corresponds to the height from the floor to the
underside of the work surface. Tighten the
locking nuts (locking nut) on the rear feet.
6. Push the dishwasher into place.
7. Finely adjust the front feet (the machine
may lean max. 5 mm) and tighten the lock-
ing nuts.
C. Adjusting machines with adjustable
foot
1. Start by measuring the height from the
floor to the underside of the work surface.
2. Install the sliding feet on the dishwasher.
3. Measure the height from the floor to the
top edge of the dishwasher.
4. Tilt the dishwasher forward a fraction and
roughly adjust the rear foot by screwing the
set screw at the front clockwise to raise or
anti-clockwise to lower (illustrated below).
Use a broad screwdriver or a hexagonal
head screwdriver.
5. Adjust the front feet by turning them clock-
wise to raise or anti-clockwise to lower.
6. Check that the height of the machine
corresponds to the height from the floor to
the underside of the work surface.
7. Push the dishwasher into place.
8. Finely adjust the feet (the machine may
lean max. 5 mm) and tighten the locking
nuts on the front feet.
3. After the steel feet have been adjusted,
screw down the two rubber feet tightly
against the floor.
The rubber feet now work as anti-tilt protection.
Steel feet
Stålfötter
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Asko D 3152 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Asko D 3152 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info