495987
30
Zoom out
Zoom in
Previous page
1/63
Next page
TD 92319GB
2006-09-22/ Ver. B
User Manual
Ascom i75 VoWiFi Handset
24
6.5 Man-down Alarm
Note: The Man-down alarm requires that the licence option is made available in the
handset. For information on how to add a licence, see A.2 Add an Alarm Licence on page
54.
You can activate/deactivate the alarm function in the menu, see 9.5.7 Deactivate/Activate
Man-down alarm
1
on page 38, or by programming a Soft/Hot key as a short-cut to the
function, see 9.5.8 Edit a Soft key on page 39. The Soft/Hot key changes the state of the
alarm, i.e. if it is deactivated it will be activated and vice verse. Press the Soft key, or press
and hold the Hot key, to put the alarm in or out of operation, respectively.
The Man-down alarm on icon on your display is an indication that the Man-down alarm is
in operation.
Send Man-down alarm
The Man-down alarm will go off when the handset is tilted more than 45º for a preset
period of time (default 30 seconds), for example if you fall. Before the alarm is activated a
warning signal sounds and the Man-down alarm on icon starts to flash. If you do not
cancel the alarm by pressing a key, it is sent and Man-down alarm is shown in the display.
Activate Man-down alarm after sending
When the man-down alarm has been sent, it is made active again by moving the handset
to upright position or pressing a key.
6.5.1 Delay Time for No-movement and Man-down Alarms Warning Signal
By setting a parameter, the time before the warning for no-movement and man-down
alarms can be delayed for ten minutes, i.e. no-movement and man-down will not be
detected during the time period. When the warning signal sounds, press the Mute button
to delay the time to next warning for up to ten minutes.
6.6 Alarm with Data
Additional data for example a location code, can be sent along with an alarm. The data
must manually be defined and stored by the user via the menu. This is a system dependent
function.
6.7 Automatic Call after an Alarm
The handset can be programmed to call a predefined telephone number directly after an
alarm. Each alarm type in the handset must be programmed with the specific telephone
number. It can be any external or internal telephone number but also a pre-defined group
of handsets.
This is a system dependent function that also require a parameter setting in the IP handset.
Note: An ongoing call will be disconnected and an incoming call will be rejected, unless it
is an alarm call, when the alarm is transmitted. Then the telephone number associated
with the alarm will be dialled.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ascom i75 VoWiFi Handset at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ascom i75 VoWiFi Handset in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info