736646
26
Zoom out
Zoom in
Previous page
1/40
Next page
26
Cleaning the device
After each use, you should clean the device
thoroughly, especially the bottom side and the
blade.
Stuck grass or dirt affect the grass discharge
and the cutting quality. For a sufficient engine
cooling, keep the engine cover, ventilation grid,
and the engine clean.
For sufficient cooling of the hydrostat transmis-
sion, keep the gearbox casing and the area
around the gearbox fan clean.
Fire hazard!Pay special attention so that
components at the silencer are clean.
For cleaning use a hand brush. Remove stub-
born soiling with a wooden or plastic spatula.
Clean the outer housing parts with a cloth.
Do not rinse off the device with a water jet or
high pressure cleaner! Do not use aggressive
cleaning agents.
General inspection
To make sure that the device can be operated
safely, check all nuts, bolts, screws, connec-
tion of fuel lines, air filters etc. regularly for firm
seating. Check the ignition wire and the spark
plug connectors for damage.
Immediately replace damaged or worn parts,
especially covers, protection skirt, silencers or
fuel tank (authorised service centre).
Check all parts that that contain fluids for leaks
and proper condition. These can be: Fuel tank,
fuel valve, fuel lines, carburetor, engine, gears,
battery, hydraulic system.
In case of leaks, contact an authorised service
centre.
Checking the safety functions
Check the safety switches for proper function.
It must not be possible to start the engine
when:
The driver does not sit on driver’s seat.
The blade clutch is switched on.
The drive lever is not in neutral position.
If the engine is running and the driver leaves
the seat, the engine must shut down.
Checking the parking brake
Warning
If the parking brake is not properly adjusted,
the device can roll away.
Make sure that the parking brake always
functions correctly.
1. Place the device on a surface with a good
grip (e.g. concrete or asphalt).
2. Switch off the engine.
3. Let the device cool down for at least
20minutes.
4. Unlock the drive.
5. Activate the parking brake.
6. Try to push the device.
If the rear wheels lock up, the parking brake is
set correctly. If the device can be pushed, the
parking brake must be readjusted by an au-
thorised service centre.
Check the foot brake (if existing)
Check if the drive lever returns to neutral posi-
tion (parking brake) when the brake pedal is
actuated.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 800 FreeRider at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 800 FreeRider in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 800 FreeRider

AS Motor AS 800 FreeRider User Manual - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info