702740
10
Zoom out
Zoom in
Previous page
1/16
Next page
determinare limpostazione per una specifica applicazione.
Impostazione Descrizione
Aperto Imposta la portata a 1,5 -7,6 m. Utilizzare per
stanze di 10 m² e oltre. Impostazione predefinita.
Chiuso Imposta la portata a 1-3 m. Utilizzare per stanze
inferiori a 10 m².
COME TESTARE IL RIVELATORE
Utilizzare il tester Sentrol 5709C per verificare la portata del rivelatore e il suo
funzionamento. Per testare il rivelatore:
1. Impostare il tester sul corretto settaggio in base al tipo di vetro. Utilizzare
limpostazione tempered se non si è sicuri del tipo di vetro.
2. Portare il rivelatore in modo test come segue:
- Tenere il tester vicino al rivelatore. Vedere figura 5.
- Attivare il tester.
Il LED sul rivelatore si illumina per 4 secondi, poi inizia a lampeggiare per
indicare che il rivelatore è in modo test. Il relè si apre per 4 secondi, poi
ritorna in standby.
3. Tenere il tester vicino alla superficie di vetro da proteggere e puntare
laltoparlante al rivelatore. Accertarsi che il tester sia nel punto sul vetro
più lontano dal rivelatore. Se vi sono tende chiuse, tenere il tester dietro
di esse. Vedere figura 6.
4. Premere il pulsante di test sul tester. Il LED sul rivelatore deve restare
acceso per 4 secondi ad indicare che il vetro si trova allinterno del raggio
di rivelazione del rivelatore. Se il LED non rimane acceso per 4
secondi, spostare il rivelatore e ripetere il test.
SPIEGAZIONE DEI LED
Il LED rosso situato sul frontale del rivelatore indica lo stato operativo dellunità
nel modo seguente:
Stato Indicazione del LED
Accensione Lampeggia allapplicazione dellalimentazione
Test battito mani /
Memoria allarme In risposta al test del battito delle mani:
Lampeggia due volte ad indicare che il rivelatore è
sotto alimentazione e funziona correttamente.
Oppure
Acceso per 4 secondi ad indicare che il rivelatore
ha segnalato un allarme.
Allarme Acceso e relè attivato per 4 secondi quando è
rilevata una rottura di vetri.
Modo test Acceso e relè attivato per 4 secondi, poi
lampeggiante per 60 secondi. Ogni test valido
resetta il tempo del modo test e il LED ricomincia a
lampeggiare per 60 secondi.
TEST DEL BATTITO DELLE MANI E MEMORIA ALLARME
La memoria allarme e il funzionamento del rivelatore possono essere verificati
con il test del battito delle mani, nel modo seguente:
1. Mettersi sotto il rivelatore e battere le mani.
2. Osservare il LED sul rivelatore.
Se il rivelatore è alimentato e funziona regolarmente, il LED lampeggia
rapidamente due volte.
Se il rivelatore ha segnalato un allarme, il LED si accende per 4 secondi.
Togliere e ripristinare lalimentazione per resettare la memoria allarme.
Il test del battito delle mani è da intendere come un test funzionale e non è
unindicazione precisa della portata del rivelatore.
Figura 6 - Come testare la portata
DATI TECNICI
Tensione di ingresso ................................................................ 9,5 -16 V DC
Corrente
Normale .................................................................................. 15 mA
Massima ................................................................................. 25 mA
Configurazione elettrica .................................................................... Form C
Caratteristiche relè ........................................................... 16 V, 50 mA max.
Caratteristiche interruttore antimanomissione ................. 12 V, 50 mA max.
Raggio di copertura ...................................................... 0,9 m - 7.6 m x 360°
Tempo di attivazione relè di allarme .................................................... 4 sec.
Dimensione vetro minima .................................................... 30,5 cm x 61 cm
Spessore vetro consigliato:
Cristallo ................................................................... 2.5 mm - 6.5 mm
Vetro temprato .......................................................... 3 mm 6.5 mm
Vetro armato .......................................................................... 6.5 mm
Laminato ................................................................................ 6.5 mm
Temperatura di esercizio .............................................................. - 50°C
Umidità relativa ...................................................10 - 90% senza condensa
Dimensioni alloggiamento rotondo .................................... 2 x 10 cm (p x Æ)
Dimensioni alloggiamento rettangolare ................ 2 x 7 x 11.5 cm (p x l x a)
Colore ................................................................................................. Bianco
Dimensioni cablaggio .................................................................. 18-24 AWG
Single
Continuous
Plate
Tempered
Laminated
Battery LED
Battery is OK if LED
stays on during test
5709C
Shatter Series Tester
Use for testing:
ShatterPro
Shatterbox
Shatterbox II
ShatterSwitch
SENTROL
J3 Connettore
a molla
Fori
Fessura
Figura 4 - Posizioni dei fori sul rivelatore
2.5 cm
Figura 5 Uso del tester
Fori
- 10 -
J3
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech SHATTERPRO 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech SHATTERPRO 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info