Manual Aritech SHATTERPRO 3 (page 2 of 16) (English, German, Dutch, Danish, French, Italian, Swedish)

702740

Zoom out

Zoom in

1/16

- 2 -

SPECIFICATIONS

Input voltage ........................................................................... 9.5 to 16 VDC

Current

Typical ..................................................................................... 15 mA

Maximum ................................................................................. 25 mA

Electrical configuration ....................................................................... Form C

Relay rating ....................................................................... 16 V, 50 mA max.

Tamper switch rating ....................................................... 12 V, 50 mA max.

Detection range ............................................................ 0.9 m - 7.6 m x 360°

Alarm response ................................................................................... 4 sec.

Minimum glass size ............................................................. 30.5 cm x 61 cm

Recommended glass thickness:

Plate ........................................................................ 2.5 mm - 6.5 mm

Tempered .................................................................. 3 mm  6.5 mm

Wired ...................................................................................... 6.5 mm

Laminated .............................................................................. 6.5 mm

Operating temperature ....................................................................0° - 50°C

Relative humidity .................................................. 10 - 90% non-condensing

Round housing dimensions: ............................................. 2 x 10 cm (D x Æ)

Rectangle housing dimensions: ....................... 11.5 x 7 x 2 cm (H x W x D)

Color ................................................................................................. White

Field wiring size ......................................................................... 18-24 AWG

SETTING THE R ANGE

The detector has a spring clip (J3) to set room size. See Figure 4. Use the

following table to determine what setting to use for an application.

Setting Description

Open Sets the range for 1.5 m to 7.6 m. Use for rooms

30 m² and larger. Default

Closed Sets the range 1 m to 3 m. Use for rooms smaller

than 30 m².

TESTING THE D ETECTOR

Use a Sentrol 5709C hand-held tester to verify detector range and operation.

To test the detector:

1. Set the tester to the appropriate glass-type setting. Use the tempered

setting if you are unsure about the glass type.

2. Put the detector in test mode as follows:

- Hold the tester close to the detector. See Figure 5.

- Activate the tester.

The LED on the detector lights for 4 seconds and then starts flashing to

indicate the detector is in test mode. The relay opens for 4 seconds, then

returns to standby.

3. Hold the tester near the surface of the glass to be protected and aim the

speaker at the detector. Be sure the tester is at the point on the glass

farthest from the detector. If closed curtains are present, hold the tester

behind them. See Figure 6.

4. Press the test button on the tester. The LED on the detector should stay

on for 4 seconds to indicate the glass is within detection range of the

detector. If the LED does not stay on for 4 seconds, move the detector

and retest.

UNDERSTANDING THE LED

The red LED located on the front of the detector indicates the status of the

unit as follows:

Status LED indication

Power on Flashes when power is applied.

Clap test/Alarm

memory In response to the clap test:

Flashes twice to indicate the detector has power

and is functioning properly.

On for 4 seconds to indicate the detector has

alarmed.

Alarm On for 4 seconds with relay when breaking glass

is detected.

Test mode On for 4 seconds with relay, then flashes for 60

seconds. Each test trigger resets the test mode

clock and the LED restarts flashing for 60

seconds.

USING THE H AND-CLAP T EST AND A LARM M EMORY

Check the alarm memory and detector operation with the hand-clap test as

follows:

1. Standing under the detector, clap your hands together.

2. Observe the LED on the detector.

If the detector has power and is functioning properly, the LED quickly

flashes twice.

If the detector has alarmed, the LED will light for 4 seconds. Cycle the

power to clear the alarm memory.

The hand-clap test is intended as a functional test and is not an accurate

indication of detector range.

J3 Spring clip

Figure 4 - Detector Knockout Locations

Figure 5  Using the Tester

Figure 6 - Testing the Range

• Single

• Continuous

Plate •

Tempered •

Laminated •

Battery LED

Battery is OK if LED

stays on during test

5709C

Shatter Series Tester

Use for testing:

ShatterPro

Shatterbox

Shatterbox II

ShatterSwitch

SENTROL

2.5 cm

Knockouts

Slot

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech SHATTERPRO 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 0,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech SHATTERPRO 3 Manual

Product: