Manual Aritech RXW8 (page 7 of 20) (English, Dutch, French, Italian)

702694

Zoom out

Zoom in

1/20

PROGRAMMING THE QUIK BRIDGE

Table 7 displays the 17 locations that can be programmed on the Quik

Bridge

Table 7: Quik Bridge

output locations and segments

0 1-4 Programming code

1 1 Output 1 event

2 Output 1 time

2 1 Output 1 Transmitter selection

2 Output 1 Special Setting

3 1 Output 2 event

2 Output 2 Time

4 1 Output 2 Transmitter selection

2 Output 2 Special Setting

5 1 Output 3 event

2 Output 3 time

6 1 Output 3 Transmitter selection

2 Output 3 Special Setting

7 1 Output 4 event

2 Output 4 time

8 1 Output 4 Transmitter selection

2 Output 4 Special Setting

9 1 Output 5 event

2 Output 5 time

10 1 Output 5 Transmitter selection

2 Output 5 Special Setting

11 1 Output 6 event

2 Output 6 time

12 1 Output 6 Transmitter selection

2 Output 6 Special Setting

13 1 Output 7 event

2 Output 7 time

14 1 Output 7 Transmitter selection

2 Output 7 Special Setting

15 1 Output 8 event

2 Output 8 time

16 1 Output 8 Transmitter selection

2 Output 8 Special Setting

17 1 On if Quik Bridge

tamper is enabled

Output event

Enter the number for the event that you wish to program for the output.

Table 8: Quik Bridge

output events

0 Zone Open

1 Zone Tamper

2 TX Low Battery

3 TX Lost

4 TX short supervision fault

5 Clean me fault

6 Zone open or tamper (default value)

7 TX lost or low battery

8 TX lost, low battery or tamper

9 Zone open, TX Lost, low battery or tamper

10 Keyfob disarm

11 Keyfob arm

12 Keyfob arm or disarm

13 Keyfob arm stay

14 Keyfob exit

15 Fob fire

16 Fob Medical

17 Keyfob panic

18 Keyfob aux 1 (Option 4 from ‘Using the 4 button keyfob)

19 Keyfob aux 2 (Option 5 from ‘Using the 4 button keyfob)

20 Receiver Jam

21 Box tamper (receiver or Quik Bridge

)

22 Receiver communication trouble

23 Receiver communication trouble, box tamper or jam

24 Reserved

25 Reserved

Output time

This can be set from 0-255 in minutes or seconds. The unit is set in the

Special Setting segment.

Special Setting

This can be set in the different bits of the segment.

Bit 1: selection of time in seconds or minutes.

• Turn bit 1 on to time the output in minutes.

• Turn bit 1 off to time the output in seconds.

Bit 2: selection of inverted output.

• Turn bit 2 on to invert output activation.

• Turn bit 2 off for normal output activation.

Important: After the walk test mode times out, the detector returns to

normal operating mode. In normal operating mode, the wireless PIR only

supervises every 2 minutes and the LED is disabled to reduce battery

consumption.

Transmitter Selection

Each bit of the segment corresponds with an output that should be

activated. Each transmitter can be set to activate 1, several or every out-

put. Turn the corresponding bit of the segment on if the transmitter should

activate the output.

Table 8: Quik Bridge

output events

CONNECTING THE QUIK BRIDGE

TO THE PANEL

The Quik Bridge

is compatible with any control panel via 8 open collector

outputs. After you have enrolled the transmitters and programmed the Quik

Bridge

, you MUST disconnect the CSX75 LCD keypad from the Quik Bridge

and the Receiver. You should then connect the Quik Bridge

to ensure that

zones 1-8 on the panel are programmed to match the programming of the

outputs on the Quik Bridge

Connect the Quik Bridge

outputs to the zone inputs on the control panel.

There are 4 ways to wire the loop receiver to the control panel. Refer to

Figures J1 through J4 for panel connections.

PROGRAMMING THE PANEL

Please refer to the panel’s instruction manual to see the steps for program-

ming the inputs.

You must ensure that the programming of the panel inputs matches the

programming of the output events on the Quik Bridge

. For example there

is no point programming an output event as 5 (Clean me fault), if there is

not an equivalent zone type on the panel.

SPECIFICATIONS

Compatibility: Control panels with hardwire loops.

Housing: RXWEH00

Receiver: RX8W8CA-Pcb

Power Requirements: 10 – 14 VDC

Current Draw: 60 mA maximum

Open Collector Outputs (1-8, B, S):

maximum applied voltage 16 VDC

maximum sink current 50 mA (typical) 15 mA (minimum)

Temperature Range: -10°C to +40°C

Dimensions: 10.31 x 13.13 x 2.5 cm (L x W x H

elpmaxE gnitteS

1tuptuoetavitcaot1rettimsnarttesoT

)1tnemges2noitacol(

-------1

tuptuoetavitcaot8dna2srettimsnarttesoT

)1tnemges4noitacol(2

8-----2-

8tuptuoetavitcaotsrettmsnart8llatesoT

)1tnemges61noitacol(

87654321

noitacoL tnemgeS noitpircseD

ataD tnevE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech RXW8 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 0,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech RXW8 Manual

Product: