702729
6
Zoom out
Zoom in
Previous page
1/16
Next page
- 6 -
Setting auto-gain:
Tone Indication Result Cause Remedy
One pulse
(Beep) Optimal sensitivity has been set OK - -
Continuous tone Optimal sensitivity cannot be set NG 1. Beam is interrupted once 1. Remove any blocking items or
(20 sec) the cover is replaced. ensure that the hand is not breaking
the beam when the cover is held in a
temporary position.
2. Beams are misaligned and 2. Check the beam power setting at
sensitivity attenuation LED lights the transmitter with the cover
attached and readjust the beam
alignment.
Tone indicator:
Test signal Alignment tone switch Other condition Description
Beam alignment ON Receiver cover detached - Reception strength monitored. Tone pitch
increases as reception improves.
Note: No tone is given if the sensitivity
attenuation LED is lit or if the receiver cover is
attached.
Walk test ON For approx. 5 minutes after - Tone is linked to the alarm LED. Both trip
gain is locked. simultaneously.
Alarm memory ON Set to manual memory. - Beep is initiated if an alarm condition occurs.
Note: This configuration is not recommended
for most security applications. The tone could
alert the intruder to detection.
Auto-gain lock ON/OFF After receiver cover is - A short tone indicates that the lock set.
attached. A continuous tone (20 sec.) indicates
readjustment.
7. TROUBLESHOOTING
Problem Possible cause Remedy
Operation LED does not light. 1. No power supply 1. Turn on the power.
2. Bad wiring connection or broken wire (short) 2. Check and correct the wiring.
Alarm LED does not light when 1. No power supply 1. Turn on the power supply.
the beam is broken. 2. Poor wiring connection or broken wire (short) 2. Check and correct the wiring.
3. Beam is reflected on to another object and 3. Remove the reflecting object or change the beam
sent to the receiver. direction.
4. Two beams are not broken simultaneously. 4. Break two beams simultaneously.
5. The beam interruption time is shorter than the 5. Adjust the beam response time.
set response time.
Alarm LED continues to light. 1. Beam alignment is out. 1. Check and adjust again
2. Shading object between the transmitter and 2. Remove the shading objects
receiver. 3. Clean the optics with a soft cloth
3. Unit optics are dirty. 4. Readjust to the same channel
4. Frequency channel is not compatible between
the transmitter and receiver
Intermittent alarms. 1. Bad wiring connection. 1. Check again.
2. Change of supply voltage. 2. Stabilize supply voltage.
3. Shading object between transmitter and 3. Remove the shading object.
receiver. 4. Change location of the installation.
4. A large electrical noise source, such as a 5. Stabilize.
power machine, is located near the transmitter 6. Clean the optics with a soft cloth.
and receiver. 7. Check and adjust again.
5. Unstable installation of transmitter and receiver 8. Increase the response time. (impossible in a
6. Dirty transmitter or receiver optics. location where the intruder can run at full speed.)
7. Incorrect alignment. 9. Set the beam power switch at H and make the
8. Small animals may be passing through the unit gain locked with the receiver cover
two beams. detached.
9. Beam power switch is set to L, which does not
keep enough sensitivity allowance.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech PB601 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech PB601 in the language / languages: English, French, Swedish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info