Manual Aritech GS110 (page 3 of 10) (Dutch)

702736

Zoom out

Zoom in

1/10

- 3 -

Installing data (Fig. 1)

- Detector range is 2 m radius on standard glass

- Always keep at least 2 cm between detector and window frame

- Glass must be at least 2 mm thick

- Each separate window pane needs one detector

- Always mount the detector on the smooth side of the window pane

- Use only on normal single pane or double glazing

Mounting (use GS117 glue kit only) (Fig. 2)

A. Spray both the back of the detector and the chosen area of the

window with the solvent provided.

B. Wipe clean with a clean dry cloth or a paper towel.

C. Spray both parts light once again.

Wait two minutes.

D. Point the activator spray-can a few cm below the mounting area on

the window and turn the spray can upwards.

Apply a thin layer of activator.

Wait five minutes.

! Be careful, the activator is flammable and may irritate the

eyes.

E. Put one drop of glue on the ceramic base of the detector and spread

evenly.

F. Place detector in position at the prepared location.

Hold in place for 30 seconds.

Wait three minutes before attempting to wire the detector.

Caution: never glue the sensor to plastic or plastic foil!

Wiring GS200 (Fig. 3)

The GS200 is not polarity dependent.

The two leads with copper cores form one set of the supply’s in/out

wires: the two leads with tinned cores form the other set supply in/out

wire (see figure 3).

Figure 4 shows the standard balanced loop with the end of line resistor.

Figure 5 shows the special requirements of BS4737.

The ES058W Junction box (Fig. 6)

It shows how a number (max.20) of GS200s might be wired using the

Aritech ES058W junction box.

Operation (Fig. 7)

In the non-alarm state a very low current flows through the loop and the

voltage on the loop remains constant.

When a detector goes into alarm it causes a short circuit, shorting out

the end of line resistor and causing the voltage to fall.

This fall in voltage is the alarm signal.

An easy way to transform this into a simple NC relay signal suitable for

any standard panel is provided by the GS218 interface.

The GS200 latches in alarm and the detector in alarm is indicated by

a latching LED.

Resetting the detector is done by interrupting the power supply.

Wiring GS110 (Fig. 8)

The GS110 is polarity dependent.

The wires coming from the GS110 are identified as follows:

a. White, tinned core : alarm loop

b. White, copper core : tamper loop

c. Black : negative

d. Red : positive

The alarm relay contact is normally closed, opening on alarm or when

power is interrupted.

Testing (Fig. 9)

Use the GS115 test unit.

- Apply GS115 test unit to the window being protected near to the de-

tector.

- Wet the surface between test unit and window for optimum trans-

mission.

Technical data GS110 GS200

Supply voltage 10-15 V dc (12 Vnom.) 8-15 V dc (12 Vnom.)

Peak to peak ripple 1 V max. (at 12 V dc) 1 V max. (at 12 V dc)

Current consumption

Normal operation 5 mA at 12 V dc <2 µA at 12 V dc

Alarm 17 mA at 12 V dc 9 mA at 12 V dc

Range on normal 2 mtr radius 2 mtr radius

glass ! 2 mm

Alarm output 100 mA at 28 V dc

Temperature limit -40 °C to +70 °C -40 °C to +70 °C

Relative humidity max. 100% max. 100%

Size 28 x 28 x 14 mm 28 x 15 x 13 mm

Weight 85 g 50 g

Housing meets IP30 IK02 IP30 IK02

(with sealed

cable entry)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech GS110 in the language / languages: Dutch as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech GS110 Manual

Product: