557694
152
Zoom out
Zoom in
Previous page
1/167
Next page
152
CS175-275-575-875 Installation Guide
27 GLOSSARY
24-hour zone
This zone remains armed the whole time unless inhibited by forced arming. It
reports as a normal burglary zone when armed.
“A” and “B” Alarm
Reporting
If a zone is defined as an A zone, an alarm is reported if a zone is activated.
If a zone is defined as a B zone, a second activation must take place within a
pre-set time. Fire and medical and personal attack zones are always treated
as A zones.
See
Location 52
on page 71 and
Location 127
to
Location 206
, starting on
page 80, for more information.
Abort
If enabled, the CSx75 waits the number of seconds programmed in location
52 prior to sending an alarm. To cancel the report, type in a code. Dialer Delay
must be enabled in the Characteristic Select of locations 127 - 206.
See
Location 52
on page 71 and
Location 127
to
Location 206
, starting on
page 80, for more information.
Mains Fail / Low Battery
Report/Warning
The CSx75 can be programmed to report mains failure and/or low battery
conditions to the central station. It can also be programmed to sound the
keypad immediately upon detection of the condition. The mains failure
report/warning can be delayed.
See
Location 51
on page 70 and
Location 52
on page 71 for more information.
Mains Power / Low
Battery Sounder Alert-
If enabled, the CSx75 beeps the keypad sounder upon arming or disarming if
the mains power is missing or a low battery has been detected.
See
Location 34
on page 65 for more information)
Access zone
This is similar to a burglary zone except that activations on these zones are
ignored during entry and exit times.
Account code
The code by which the ARC/central station identifies and charges the user.
ARC (alarm report
centre)
This is the place contacted via telephone when an alarm takes place. It is also
known as a control station or a central station.
Arm / Disarm Codes
The CSx75 can have four-digit codes or six-digit codes to arm/disarm the
control. All codes must have the same number of digits. The factory default for
User #1 is 1122 when using a four-digit code, or 112256
for a six-digit code.
This code can then be used to enter the new arm/disarm codes.
See
Location 53
on page 71 for more information.
Armed
The security system is on.
Autotest
This feature causes the panel to call the central station to report a
communicator test at a specified interval.
See
Location 63
and
Location 64
on page 75 for more information.
152


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech CS275 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech CS275 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aritech CS275

Aritech CS275 Additional guide - Dutch - 2 pages

Aritech CS275 Additional guide - Dutch - 20 pages

Aritech CS275 User Manual - Dutch - 23 pages

Aritech CS275 Installation Guide - Dutch - 166 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info