557694
53
Zoom out
Zoom in
Previous page
1/167
Next page
CS175-275-575-875 Installation Guide 53
12.5 Defining the country code
1. Enter programming mode as described in
Entering programming mode
on page
54.
2. Press 0# for the controller.
3. Press 0# for the first location in the controller.
4. Enter the country code and press
. When this location is changed from the
keypad, the panel returns to the default country settings.
12.6 Programming via the LED keypad
12.6.1 Entering programming mode
1. Press
8
.
2. Enter a Go to program code.
3. The Service LED blinks, prompting you to enter a module number.
4. Enter the module number and press #.
5. The Armed LED lights, prompting you to enter a programming location.
6. Enter the location number and press #. If the location is valid, the Armed LED
turns off, the Ready LED lights up and the binary data for the first segment of the
location is shown by the zone LEDs. While you are entering new data, the Ready
LED flashes to indicate that a data change is in process. The flashing continues
until the new data is stored.
7. Press to save any changes you have made. The keypad displays the data in
the next segment.
8. Repeat steps 4 to 7 until the last segment is reached.
9. Press # to exit the location.
10. The Armed LED lights up, prompting you to enter a new programming location.
"
You cannot enter programming mode if the system or any partition is armed. The timeout
for programming mode is 15 minutes.
12.6.2 Exiting a location
When you have programmed the last segment of a location, press to exit the
location and save the data. The Ready LED turns off.
To exit before the last segment, press #. Any changes you have made are not saved.
You can then enter another programming location.
12.6.3 Exiting programming mode
Press the Exit key to leave the current programming level.
If you do not want to program additional modules, press the Exit key again to exit
programming mode.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech CS275 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech CS275 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aritech CS275

Aritech CS275 Additional guide - Dutch - 2 pages

Aritech CS275 Additional guide - Dutch - 20 pages

Aritech CS275 User Manual - Dutch - 23 pages

Aritech CS275 Installation Guide - Dutch - 166 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info