Manual Aritech CD95 (page 15 of 24) (English)

557687

Zoom out

Zoom in

1/24

142360999-2

ADVISOR







CD 7203

CD95/15003

User Manual

Software from version: V6.0



stored in a retrieval system, or transmitted in any form, or by any means - electronic,

photocopying, recording, or otherwise - without the prior written permission of SLC BV.

DISCLAIMER

SLC BV makes no representations or warranties with respect to the contents hereof and

specifically disclaim any implied warranties of merchantability or fitness for any particular

purpose. Further SLC BV reserve the right to revise this publication and to make changes from

time to time in the contents hereof without the obligation of SLC BV to notify any person of

any such revision.

User Manual for CD72/95/15003

Page 3

ONTENTS

INTRODUCTION ..................................................................................................................................... 4

USING THE KEYPAD.............................................................................................................................. 5

The CD3008 keypad............................................................................................................................. 5

The display........................................................................................................................................... 6

The LEDs ............................................................................................................................................. 6

USING A SINGLE ALARM SYSTEM...................................................................................................... 7

Arming a system................................................................................................................................... 7

Arming a system with open zones........................................................................................................ 8

Disarming a system.............................................................................................................................. 9

Disarming a system after an alarm .................................................................................................... 10

USING A SPLIT SYSTEM..................................................................................................................... 11

Arming a split system .........................................................................................................................12

Arming a split system with open zones .............................................................................................. 13

Disarming a split system .................................................................................................................... 15

Disarming a split system after an alarm ............................................................................................. 16

UPLOADING AND DOWNLOADING IN THE CD72 AND THE CD95.................................................. 18

OVERVIEW OF THE OPTIONS AVAILABLE....................................................................................... 19

Option list for the CD72/95/150..........................................................................................................19

Page 4 User Manual for CD72/95/15003

NTRODUCTION

Thank you for choosing an ARITECH security system. When properly maintained, the system will

provide years of reliable operation.

This manual explains how to use the ARITECH CD72 and CD95 series for every day use. There is a

more detailed manual available for managers which explains how to carry out a wider range of

operations. These instructions apply to both the CD95 and CD150.

The CD95 is a burglar alarm system which can detect an (attempted) break-in using connected

detectors, magnetic contacts, etc., generating an alarm. The CD72 can be divided into two

independent systems, and the CD95 into eight independent systems.

The manual uses symbols to show when you must enter information into the keypad, and when the

system emits a beep. Examples of these symbols are shown below:

code +

You need to enter information into the keypad. What you have to enter is on the

right of the symbol. In this example you should enter your code and then press the

Accept key (

Beeeep

The buzzer on a key switch or keypad emits a long beep. Short beeps can also be

emitted - this is indicated with the text ‘

Beep Beep

’.

Your system has been programmed with one or two entrance times and one exit time. These are pre-

set amounts of time that let you enter and leave the premises through specific routes without activating

an alarm. Be sure you know which routes you can use to leave and enter the premises.

Entrance time: _________________ seconds Exit time: _________________ seconds

Second entrance time: _________________ seconds

User Manual for CD72/95/15003

Page 5

SING THE KEYPAD

This chapter describes the alarm system keypad.

CD3008

KEYPAD

The keys

0 - 9

These keys are used to enter your code. Always begin with zero (0) and then

enter your code. After entering the code, you can carry out the operations

assigned to it.

The options assigned to a code can be adjusted by the installer or manager.

When you are in an option list, this key can be used to go backwards in the

list. During arming you can exclude zones. See

Special keys

This key has several functions. When you are in an option list, you can use it

to move forward through the list. The other options are listed under

Special

keys

This key is the

key. It is used to confirm that the option shown in the

display should be implemented.

This is the

Reject

key. It is used to indicate that the option shown has not

been changed or that you want to exit the option list.

Special keys

The following key combinations can be programmed by the installer. They may not be active in your system.

"#"#

Pressing these keys simultaneously will activate a personnel attack alarm. A

report can then be sent over the phone lines to the central station, and the

bells and flashing light may be activated.

####

Press the

‘

key twice to see which zones are still open. All the open zones

are displayed or the message ‘

All Closed’

appears.

""""

Press the

‘

key twice to see which zones are inhibited. All the inhibited

zones are displayed or the message ‘

No Inhibits’

appears.

If the system is split you must indicate which system you want information about. Systems which are armed or have

been triggered cannot be selected.

Page 6

User Manual for CD72/95/15003

HE DISPLAY

The display is the link between you and the security system. The text messages displayed show where

and when faults or alarms have occurred. The display can also show a list of operations from which

you can select.

Examples of the messages which can appear include:

TUE 23 APR 07.40

The date and time are always displayed, regardless if the system is

armed or not. You can ask the installer to replace it with another

message, if you want.

Arm Menu

If you press Accept (

), you enter an option list. This option list can

be used to determine the method used arm the system.

Area 1 Arming

The system is being armed. Leave the secured area now.

Area 1 Armed

The system is armed.

Not all the messages may appear on your display: it depends how the system has been programmed.

It can show you only the messages you want to see, or those you are authorised to see.

LED

There are

three

coloured LEDs (light emiting diodes) on the keypad that let

you quickly see if there is a problem.

Green LED

Power

The mains power is on. If it has not been illuminated for a hour and

a power cut is not apparent, contact your installer.

Yellow LED

Trouble

If the yellow LED is on, there is a problem in the panel. The type of

problem is shown in the display. Contact your installer. Problems

that may occur include:

♦

Battery fault

♦

Fuse fault

♦

Line fault (if a dialler is connected)

♦

RKP fault (problem with keypads)

EEPROM fault (problem in the system)

Red LED

Alarm

The alarm is activated. The bells, keypad buzzers and flashing light

may also be active. If a dialler is connected, the alarm is reported to

the central station. When you enter your code, the system disarms,

the bells and the flashing light are switched off, and the central

station receives the report that the alarm has been deactivated.

The red LED will also illuminate if you disturb an alarm zone during

the exit period, and the bells and dialler will be activated.

User Manual for CD72/95/15003

Page 7

SING A SINGLE ALARM SYSTEM

This chapter

explains how to switch on and off an alarm system for premises with only one alarm

system. These instructions also apply to users who only have access to a single alarm system in the

premises, although several systems may actually be present.

Depending on how the system has been programmed, you may not need to do all the steps shown in

the instructions.

If you enter the wrong code 10 times consecutively, the system is automatically locked for 90 seconds.

During this time you cannot access the system.

RMING A SYSTEM

Before you can arm, that is switch on, the alarm system, all intrusion zones must be secure. If a zone

in the premises is ‘open,’ that is its doors, windows, etc. are not properly closed, you will not be able to

set the alarm in that zone, and the message ‘Open zones’ will appear on the display. It will also show

you which zone(s) are open. You must then check that the doors, windows, etc. protected by the

zone(s) shown on the display are properly closed.

1. Go to the keypad. The current date and time appear on

the display. An example is shown.

TUE 23 APR 07.39

2. Press the key

and then enter your code. A ‘*’ appears in

the display for every key you press. Use the

key to

cancel an incorrect entry and to restart a new entry code.

Enter Code

0 + code

Enter Code ****

Arm Menu

3. Press the

key.

Normal Set

4. Press the

key again.

If the system cannot be armed because there are area(s)

in the premises which are not properly secured, the

message

‘Open Zone(s)

’ will appear and a list of the

zone(s) not closed. Press the

key to quit and check the

doors, windows, etc. of the zone(s) identified.

Normal Set

For information about excluding open zones, refer to the

section ‘Arming a system which has open zones’ on page

The alarm is being set.

System Arming

The buzzer begins to beep. You must now exit the

protected area by the designated route.

Leave now

Page 8

User Manual for CD72/95/15003

Beeeep

The alarm is now set.

System Armed

The current date and time automatically appears.

TUE 23 APR 07.40

RMING A SYSTEM WITH OPEN ZONES

When arming (switching on) the system, you may get the message

‘Open Zone(s)’

along with a list of

the zones in the premises that have not yet been closed. You should close these zones and then retry

arming the system. However, occasionally you may not be able to close an open zone because, for

example, a door lock or magnetic contact may be malfunctioning. You can exclude this open zone from

the system (called inhibiting a zone).

Only use this exclusion option when absolutely necessary as any inhibiting of zones will reduce the

security level of your system.

Although you can exclude an open zone when the tamper alarm has been triggered (identified by the

letter ‘T’ in front of the open zone listed), you will not be able to arm the system until the tamper alarm

has been rectified.

1. Go to the keypad. The current date and time appear on

the display. An example is shown.

TUE 23 APR 08.21

2. Press the key

and then enter your code. A ‘*’ appears in

the display for every key you press. Use the

key to

cancel an incorrect entry and to restart a new entry code.

Enter Code

0 + code

Enter Code ****

Arm Menu

3. Press the

key.

Normal Set

4. Press the

key again.

Normal Set

System Arming

The system has identified zones in the premises that are

not properly closed.

Open Zone(s)

It then proceeds to list the open zone(s). In this example,

zone 2 ‘Hall’ is open.

002 Hall

5. Press

"$"$

to exclude a zone from the system.

Inhibit Zone ___

User Manual for CD72/95/15003

Page 9

6. Press the number of the open zone, in this example ‘2.’

Inhibit Zone 2

The system then confirms which zone you have excluded.

002 Hall

If another zone is open, it will be listed and you must

again press

and the zone number to inhibit it.

Is Inhibited

The alarm is being set.

System Arming

The buzzer begins to beep. You must now exit the

protected area by the designated exit route.

Leave now

Beeeep

The alarm is now set.

System Armed

The current date and time will automatically appear.

TUE 23 APR 08.22

ISARMING A SYSTEM

If you enter the premises when the system is armed, the buzzer will begin to beep (if programmed) with

an intermittent tone to indicate that the entry period has begun. As long as this beeping continues, you

can disarm (switch off) the system with your code without activating an alarm. You must not enter other

areas of the system during the beeping. If you do, a siren will sound and a full alarm condition may

occur. The entry period (length of time of the beeping) is programmed by the installer.

1. Go to the keypad. The entry period starts as soon as you

open the entrance door, or when you enter the entry

zone. You can switch off the system without activating the

alarm as long as the beeping continues.

Beep Beep

The current day, date and time are displayed. An example

is shown.

TUE 23 APR 07.39

2. Press the key

and then enter your code. A ‘*’ appears in

the display for every key you press. Use the

key to

cancel an incorrect entry and to restart a new entry code.

Enter Code

0 + code

Enter Code ****

Disarm?

3. Press the

key.

Finished?

4. Press the

key to confirm that you have finished.

Steps 3 and 4 may be automated by the system. If so,

you will not have to press the

key.

TUE 23 APR 07.40

Page 10

User Manual for CD72/95/15003

ISARMING A SYSTEM AFTER AN ALARM

The bell and the flashing light are activated when an alarm is triggered in the system. If your system

has the option, a report of the event is automatically sent over the phone lines to a central station. If

you inadvertently activate an alarm, immediately telephone the central station to prevent an

unnecessary response.

When you enter the premises after an alarm, the bell may already be silent if it has been so

programmed. This allows there to be several alarms. Remember to record the fault or alarm in your

logbook for future reference.

1. Go to the keypad. The entry period starts as soon as you

open the entrance door, or when you enter the entry

zone. You can switch off the system without activating the

alarm as long as the beeping continues.

The red

ALARM

LED is lit on the control panel.

Beep Beep

The current day, date and time are displayed. An example

is shown.

TUE 23 APR 07.39

2. Press the key

and then enter your code. A ‘*’

appears in the display for every key you press. Use the

key to cancel an incorrect entry and to restart a new entry

code.

Enter Code

0 + code

Enter Code ****

Disarm?

3. Press the

key.

A list of triggered zones will be displayed.

Events in Log...

In this example, the alarm was triggered in zone 4 ‘Back

Door’ on 23 April at 5.20 am in area 1.

004 Alarm

004 Back Door

23 APR 05.20 A1

4. Press the

key to confirm the alarm.

System Disarmed

TUE 23 APR 07.40

Step 3 above may be automated by the system. If so, you will not have to press the

key.

RECORD THE FAULT OR ALARM IN YOUR LOGBOOK !

User Manual for CD72/95/15003

Page 11

SING A SPLIT SYSTEM

When the system was installed it was divided into different security areas. A system that has more than

one security area it is called a split system. These different areas were programmed by the installer.

Depending on how the system was programmed, your code may give you access to one or more of the

security areas.

Depending on how the system has been programmed, you may not need to do all

the steps shown in the instructions.

If you enter the wrong code 10 times consecutively, the system is automatically locked for 90 seconds.

During this time you cannot access the system.

A split system has two different standby displays. This is the display you see when you approach the

keypad. They are called ‘Time/Date display’ and ‘Status display.’ The installer programmes one of

these versions in your system.

Time/Date display:

It shows the current day, date and time. The system can also be

programmed to present a second display to show a message, such

as your company name for example.

TUE 23 APR 07.40

Status display:

It shows all the areas in the system (up to eight) and their security

status. There are five different labels to identify the status of an area.

If there are more than four areas, they will be shown in a second

display.

[

]

=2= <3> 4

[

]

[

]

=2=

<3>

square brackets. The area is armed.

(number flashing). Area number displayed is in alarm.

equal signs. The area is being armed (the exit time is still operating).

pointed brackets. The area is partially armed (partguard).

no brackets. The area is disarmed.

After entering your code, you will see one of two ‘selection’ messages. Which message you get

depends on which one the installer programmed. They are as follows:

1. The system lists the status of each area, one display per area. At

the end of the list you can enter the area number you want to

Area 1 Armed

access. If you do not enter a number, the standby display will

reappear.

Area 2 Disarmed

Enter Area No.

2. The system lists the status of all the disarmed areas (underscore

scrolls underneath the numbers). If there are more than four areas,

[

]

<3> 4

they will be shown in a second display. You can then enter the area

number you want to access. If you do not enter a number, the

standby display will reappear.

Enter Area No.

Page 12

User Manual for CD72/95/15003

RMING A SPLIT SYSTEM

As explained at the beginning of the chapter “Using a split system,” a split system can be programmed

to show two different standby message displays, and two different ‘selection’ messages after entering

your code. The instructions below use the displays “Time/Date” and “Area

[

number

]

armed.”

If your code lets you access more than one security area, you can select one of them to arm.

1. Go to the keypad. The current date and time are

displayed. An example is shown.

TUE 23 APR 07.40

2. Press the key

and then enter your code. A ‘*’ appears in the

display for every key you press. Use the

key to cancel an

incorrect entry and to restart a new entry of the code.

Enter Code

0 + code

Enter Code ****

In this example, areas 1 and 2 are disarmed.

Area 1 Disarmed

Area 2 Disarmed

You have a few seconds to enter the number of the area

you want to arm.

Enter Area No.

3. Enter the area number (in this example it is 1).

Arm Menu

4. Press the

key.

Normal Set

5. Press the

key again.

If you want to exclude zones in the area (open zones), press

the arrow key (

↑

). This feature is explained in the section

“Arming a system which has open zones.” Otherwise do

nothing: the message ‘Area 1 Arming’ appears automatically.

Normal Set

Area 1 Arming

Area 1 is arming. If programmed, the buzzer for the

system will begin.

Beeeep

Leave Now

Area 1 Armed

Area 2 Disarmed

Enter Area No.

6. If you also want to arm area 2, enter the number 2 into

the keypad.

Arm Menu

User Manual for CD72/95/15003

Page 13

7. Press the

key again.

Normal Set

Area 2 is arming. If programmed, the buzzer for the area

will begin.

Area 2 Arming

Beeeep

You must exit the protected area by the designated exit

route.

Leave Now

Area 1 Armed

Both areas are now armed.

Area 2 Armed

Enter Area No.

TUE 23 APR 07.41

RMING A SPLIT SYSTEM WITH OPEN ZONES

When arming (switching on) the alarm, you may get the message

‘Open Zone(s)’

along with a list of

the zones in the premises which have not yet been closed. You should close these zones and then

retry arming the alarm. However, occasionally you may not be able to close an open zone because, for

example, a door lock or magnetic contact may be malfunctioning. You can then exclude this open zone

from the system (called inhibiting a zone). A split system lets you control open zones in specific areas

of the premises.

Only use this exclusion option when absolutely necessary as any inhibiting of zones will reduce the

security level of your system.

Although you can exclude an open zone when the tamper alarm has been triggered (identified by the

letter ‘T’ in front of the open zone listed), you will not be able to arm the system until the tamper alarm

has been rectified.

As explained in section “Arming a split system,” a split system can be programmed to have two

different standby message displays, that is the message you see when you approach the keypad, and

two different messages immediately after entering your code into the keypad. The instructions below

use the displays “Time/Date” and “Area

[

number

]

armed.”

If your code lets you access more than one security area, you can select one of them to arm.

1. Go to the keypad. The current day, date and time are

displayed. An example is shown.

TUE 23 APR 08.21

2. Press the key

and then enter your code. A ‘*’

appears in the display for every key you press. Use the

key to cancel an incorrect entry and to restart a new entry

of the code.

Enter Code

Page 14

User Manual for CD72/95/15003

0 + code

Enter Code ****

In this example, areas 1 and 2 are disarmed.

Area 1 Disarmed

Area 2 disarmed

You have a few seconds to enter the number of the area

you want to arm.

Enter Area No.

3. Enter the area number (in this example it is 1).

Arm Menu

4. Press the

key.

Normal Set

5. Press the

key again.

Normal Set

The system has identified zones in the area that are not

properly closed.

Open Zone(s)

It then proceeds to list the open zone(s). In this example,

zone 2 is open. The display is blinking.

002 Hall

6. Press

"$"$

to exclude a zone from the area.

Inhibit Zone ___

7. Press the number of the open zone, in this example ‘2.’

Inhibit Zone 2

The system then confirms which zone you have excluded.

002 Hall

If there still is a zone open, it will be listed, and you must

again press

and the zone number to inhibit it.

Is Inhibited

The alarm is being set.

Area 1 Arming

8. The buzzer begins to beep. You must now quit the

secured area.

Beeeep

You must now exit the protected area by the designated

exit route.

Leave now

The alarm is now set.

Area 1 Armed

Area 2 Disarmed

Enter Area No.

TUE 23 APR 08.22

User Manual for CD72/95/15003

Page 15

ISARMING A SPLIT SYSTEM

If you enter the premises when the system is armed, the buzzer will begin to beep (if programmed) with

an intermittent tone to indicate that the entry period has begun. As long as this beeping continues, you

can disarm (switch off) the system with your code without activating an alarm. You also must not enter

other areas of the system during the beeping. If you do, a siren will sound and a full alarm condition

may occur. The entry period (length of time of the beeping) is programmed by the installer.

1. Go to the keypad. The entry period starts as soon as you

open the entrance door, or when you enter the entry

zone. You can switch off the system without activating the

alarm as long as the beeping continues.

Beep Beep

The current day, date and time are displayed. An example

is shown.

TUE 23 APR 07.39

2. Press the key

and then enter your code. A ‘*’

appears in the display for every key you press. Use the

key to cancel an incorrect entry and to restart a new entry

of the code.

Enter Code

0 + code

Enter Code ****

In this example, area 1 is armed and area 2 disarmed.

Area 1 Armed

Area 2 Disarmed

You have a few seconds to enter the number of the area

you want to switch off.

Enter Area No.

3. Enter the area number (in this example it is 1).

Disarm?

4. Press the

key to confirm you want to switch off

area 1.

Area 1 Disarmed

Finished?

5. Press the

key to confirm you have finished.

Area 1 Disarmed

Area 2 Disarmed

6. If you want to disarm or modify another area, enter its

number.

If you are finished, do nothing. The standby display

message will automatically appear after a few seconds.

Enter Area No.

Steps 4 and 5 may be automated by the system. If so,

you will not have to press the

key.

TUE 23 APR 07.40

Page 16

User Manual for CD72/95/15003

ISARMING A SPLIT SYSTEM AFTER AN ALARM

The bells and the flashing light are activated when an alarm is triggered in the system. If your system

has the option, a report of the event is automatically sent over the phone lines to a central station. If

you inadvertently activate an alarm, immediately telephone the central station to prevent an

unnecessary response.

When you enter the premises after an alarm, the bell may already be silent if it has been so

programmed, but the red LED will still be activated. This allows there to be several alarms. Remember

to record the fault or alarm in your logbook for future reference.

If your code allows you to access more than one security area, you can select one of them to disarm.

1. Go to the keypad. The entry period starts as soon as you

open the entrance door, or when you enter the entry

zone. You can switch off the system without activating the

alarm as long as the beeping continues.

The red LED

ALARM

is lit on the keypad.

Beep Beep

The standby display is displayed. An example is shown.

TUE 23 APR 07.39

2. Press the key

and then enter your code. A ‘*’ appears in

the display for every key you press. Use the

key to

cancel an incorrect entry and to restart a new entry of the

code.

Enter Code

0 + code

Enter Code ****

In this example, the area 1 alarm has been triggered and

area 2 is armed.

Area 1 Alarm

Area 2 Armed

Enter Area No.

3. Enter the area number where the alarm occurred (in this

example it is 1). You have a few seconds to enter the

number.

Disarm?

4. Press the

key to disarm the selected area (area 1

in this example).

A list of where the alarm was triggered is presented.

Events in Log...

In this example, the alarm was triggered in zone 4 ‘Back

Door’ on 23 April at 7.40am in area 1.

004 Alarm

004 Back Door

23 APR 05.20 A1

5. Press the

key to confirm the alarm.

Area 1 Disarmed

User Manual for CD72/95/15003

Page 17

If there are other alarms, they are shown one after another.

A summary of the status of the areas appears. If you wish to

make more changes, enter the number of the area you want to

change. Otherwise the standby message automatically appears.

Area 2 Armed

Enter Area No.

TUE 23 APR 07.40

RECORD THE FAULT OR ALARM IN YOUR LOGBOOK !

Page 18

User Manual for CD72/95/15003

PLOADING AND DOWNLOADING IN THE CD

AND

THE CD

The CD72 and CD95 series has the option of controlling, modifying and programming the alarm

system remotely by the installer. With the use of a modem messages can be sent from the control

panel to a personal computer (PC), called uploading, and from a PC to the control panel, called down

loading. Uploading and downloading is therefore a quick and handy aid to easily discovering and

solving problems.

A connection can be established in the following ways:

1 . By dialling into the alarm system. The installer dials in to your alarm system. The dialler will

then accept and check whether the connection can be established. The dialler then calls

the installer back. This ensures that nobody other that the installer can gain access. When

the connection has been established

‘OK’

appears in the display.

2. By entering a up/down (U/D) load code. This is a code which you can enter when the

display is showing the time and date. If the code is correct, ‘

OK’

appears in the display and

the dialler then calls your installer and establishes a connection.

When the connection has been established

‘U/D code’

appears in your display. You can no longer

control your system from that moment until the time and date reappear in the display.

User Manual for CD72/95/15003

Page 19

VERVIEW OF THE OPTIONS AVAILABLE

The following flowchart provides an overview of all the options available from the CD72 and CD95/150

alarm systems. It also shows the keypad keys you need to press in order to arrive at the options.

Options listed below in grey are only available for the CD95/150 alarm system. The symbols used to

represent the keys are as follows:

Accept X Reject

↓

Move forward

↑

Move backward

PTION LIST FOR THE

CD72/95/150

There are nine main menu options in this system. Depending on how the system has been

programmed, your code may not give you access to all of the options. If you want to access more

options than you currently are able to, contact your installer.

The menu options let you carry out the following operations:

Name of menu option What it lets you do

1. Arm Menu There are four sub-options, each allowing you to carry out a different

operation:

•

Normal Set Set the alarm

•

Partguard Set the alarm with zones excluded by the

installer

•

Set (No Buzzer) Set the alarm with no exit time

•

Forced Arm Set the alarm with all open zones

inhibited, except exit/entry zone(s) and access

zone(s)

•

Delay AutoArm Delay time of auto alarm

•

AADly Until

[

time

]

Set time of auto alarm

•

AA Ignore Off Ignore next auto alarm

•

Set Manager Slot Programming of an extra holiday slot

•

Previous Menu Return to menu

2. Inhibit Exclude open zones from a security area

3. Walk/Bell/Ch Test Test if detectors, internal/external bells are OK/ switch chime on or off

4. Light Menu Turn on external/internal lights

5. Unlock Unlock a door

6. E. Log/Time/Date Engineers log, listing all events in the system, print log, and changing

the standby date and time

7. Change Codes Change own code(s) (if programmed other codes and user names)

8. Operator Log Detailed list of activation and system operations. This log will be

cleared each time the system is armed

9. Finished? Exit to time and date display

Page 20

User Manual for CD72/95/15003

Flowchart of the CD72/95/150 User Options

User Manual for CD72/95/15003

Page 21

Page 22

User Manual for CD72/95/15003

Page 23

Page 24

User Manual for CD72/95/15003

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech CD95 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aritech CD95

Aritech CD95 Additional guide - Dutch - 80 pages

Aritech CD95 User Manual - Dutch - 23 pages

Aritech CD95 User Manual - Dutch - 108 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech CD95 Manual

Product: