702287
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
Merk: Standardmelding nummer 0 = ingen melding
Obs: Rapporteringskode 12 (130, BA Innbrudd) og
rapporteringskode 1 (Innbruddsalarm) er samme hendelse.
Hvis rapporteringskode 12 (130, Innbrudd) er programmert
med en alarmmelding, vil denne overstyre rapporteringskode 1
(Innbruddsalarm)Innbrudd) er programmert med en
alarmmelding, vil denne overstyre rapporteringskode 1
(Innbruddsalarm)
1 (Innbruddsalarm) er samme hendelse. Hvis
rapporteringskode 12 (130, Innbrudd) er programmert med en
alarmmelding, vil denne overstyre rapporteringskode 1
(Innbruddsalarm).
(Innbruddsalarm) er samme hendelse. Hvis rapporteringskode
12 (130, Innbrudd) er programmert med en alarmmelding, vil
denne overstyre rapporteringskode 1 (Innbruddsalarm).
TEKNISKE SPESIFIKASJONER
Strømforsyning
12 gjennom flatkabel
fra sentralapparat
Forsyningsstrøm 50 mA
Innspillingskapasitet 8 meldinger (total
spilletid – 35 sek.)
Båndbredde for innspilling 3 kHz
Størrelse 80 mm x 50 mm x 20
mm
Vekt 123 g
Temperatur 10°C til +50°C
Ikke-flyktig minne Ja, midlertidig (minst 5
timer)
Automatisk
signalstyrkekontroll under
innspilling
Ja
Bekreftelse vha. DTMF-
kode
"0"
Módulo de
informe de voz
¿PARA QUÉ SIRVE?
La unidad ATS7200 permite informar de eventos, mediante la
reproducción de mensajes pregrabados, a 1, 2, 3 o 4
ubicaciones (receptoras). Los informes de voz se transmiten a
través del marcador integrado del panel de control (RTC) o a
través del módulo RDSI opcional.
MENSAJES SENCILLOS Y MÚLTIPLES DEL MÓDULO DE VOZ
Se pueden instalar un máximo de dos módulos de informes de
voz. Cada módulo cuenta con ocho mensajes: el mensaje
principal, el mensaje de la dirección y seis mensajes de
alarma. Si se instala un segundo módulo, los ocho mensajes
del segundo módulo serán mensajes de alarma (vea la tabla 1
de la página 2).
ANTES DEL MONTAJE
La unidad ATS7200 se monta en una caja de panel ATS.
Importante:
1. Desconecte la alimentación antes de abrir la caja.
Desconecte el enchufe de la pared.
O BIEN
Desconecte la alimentación mediante un circuito de
protección.
2. Desconecte la batería (si la hay).
MONTAJE DE LA UNIDAD (VEA LAS ILUSTRACIONES y )
Montaje de la unidad ATS7200 en el panel de control
(ATS2000/3000/4500)
1. Sitúe las sujecciones en los agujeros cuadrados (4); utilice
los separadores metálicos si los hay.
2. Utilice tornillos para montar la unidad ATS7200.
Montaje de la unidad ATS7200 en el panel de control
(ATS4000/2300/3300)
1. Retire los tornillos (1) y separe el PCB del panel de
control.
2. Sitúe los separadores de ampliación con las arandelas
de plástico en la parte superior de los separadores
existentes (3).
3. Sitúe las sujecciones en los agujeros cuadrados (4).
4. Monte la unidad ATS7200 con los tornillos y los
separadores de ampliación (5).
5. Coloque en su sitio el PCB del panel de control ATS.
Conexión del módulo de voz
1. Conecte el cable plano (2) entre el panel de control
(conector J20) y la unidad ATS7200 (conector CONN1 o
CONN2).
2. Conecte la línea telefónica al panel de control o al módulo
RDSI.
DESCRIPCIÓN DE LA UNIDAD ATS7200 (VEA LA ILUSTRACIÓN
)
Nº Descripción Función
1. CONN 1/CONN 2
(Conectores de
sistema)
Comunica la unidad
ATS7200 con el panel
principal.
2. CONN 3 Para grabar y comprobar
mensajes.
3. Pulsador Controla la grabación y la
comprobación de los
mensajes.
4. Puentes Seleccionan direcciones
esclavas adicionales, en el
caso de que se utilice más
de un módulo de informes
de voz en el mismo panel.
5. Condensador Gold
Cap
Se utiliza para guardar
mensajes durante fallos
breves de alimentación.
6. LED Indica que hay una conexión
de +12 V de CC.
SELECCIÓN DE DIRECCIONES DEL BUS MI Y
POSICIONAMIENTO DE LOS PUENTES
Tres puentes determinan la dirección de la unidad ATS7200
en el bus MI. Estos puentes están situados junto al
condensador Gold Cap y llevan las etiquetas A0, A1 y A2
respectivamente. Si sólo se utiliza un módulo, todos los
puentes estarán presentes. Para utilizar el segundo módulo,
habrá que retirar el puente A0.
Nota: Los puentes A1 y A2 se utilizan para funciones de las
que se hablará en otra sección de este manual.
Dispositivo Puentes
A0 A1 A2
Módulo 1 I I I Predeterminado I = Insertado
Módulo 2 R I I R = Retirado
SECUENCIA DE LOS INFORMES
La unidad ATS7200 emite en primer lugar el mensaje principal
(1), seguido de uno o más mensajes de alarma (3 al 8) y, por
último, el mensaje de la dirección (2). El mensaje principal se
llega a repetir hasta 10 veces, a no ser que el usuario pulse
"0" para pasar al mensaje de alarma. Si el usuario no pulsa "0"
a tiempo, el panel corta la conexión y lo intenta de nuevo más
tarde. Si hay una segunda unidad ATS7200 instalada, los 8
mensajes de la segunda unidad son mensajes de alarma. Por
tanto, los mensajes que van del 3 al 16 están destinados a
mensajes de alarma. (Nota: El tiempo total de grabación para
los 8 mensajes es de 35 segundos).
ES
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS7200 in the language / languages: English, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info