Manual Aritech ATS1290 (page 2 of 24) (English, German, Dutch, Danish, French, Italian, Finnish)

702281

Zoom out

Zoom in

1/24

ATS129

IADS DGP available menus

1-DGP Status

0-Exit, Menu:

Operating

*=-,#=+,0=Exit

Dev:16 A:0 T:0

*=-,#=+,0=Exit

DGP1 I:17-32 O:17-32

*=-,#=+,0=Exit

V-bus: 12,7 Vdc

*=-,#=+,0=Exit

I-bus: 3 mA

*=-,#=+,0=Exit

2-Device Status

0-Exit,Menu:

17/0,PIR,T0

Input No:

17/0, Normal

*=-,#=+,0=Exit

3-Device Settings

0-Exit,Menu:

17/0,PIR,T0

Input No:

17/0,Loc1:0

*,Value:

17/0,1:00000000

*,Bits:

4-Reset Settings

0-Exit,Menu:

17/0,PIR,T0

Input No:

17/0,Reset(Y/N)?

*=Yes,#=No

5-Learn Mode

0-Exit,Menu

Start Learn Mode?

*=Yes,#=No:

6-DGP Mode

0-Exit,Menu:

1 DGP address

*=Change,#=Enter

Extended Mode

*=Change,#=Enter

7-Factory Defaults

0-Exit,Menu:

Set Factory Defaults?

*=Yes,#=No:

ATS129

IADS DG

Introduction

The ATS1290 is an interface between the ATS LAN bus and an IADS bus

(Intelligent Addressable Device System bus). It provides two-wire

bidirectional communications with up to 32 individually addressed IADS

modules. It is intended to be sitting on the LAN of any existing

configuration of ATS products to expand the system with addressable

modules. A maximum of 15 ATS1290 DGPs can be connected to the

LAN.

Mounting the unit

Mount the ATS1290 PCB in any existing ATS series enclosure that

supports the BB format.

Connections CON1 (see fig ,  and )

COMMS

12 VDC power supply. It is recommended that where the

distance between an ATS1290 and the nearest device is

more than 100 meters, a separate power supply be

used. Refer to the Remote DGP section. When using an

external power supply, use a fused power output (1 A

fast).

COMMS

D+

D -

Positive and negative data connection of the system

databus. Units can be up to 1.5 km from the ATS control

panel, depending on the cable used. See the ATS control

panel installation guide for details.

TAMP

The PCB tamper switch is connected in parallel to the

external tamper connection. Tamper switch requires

normally open contacts.

 Depending on the type of housing used, you can use the PCB

tamper or connect an external tamper.

CON10 (see fig , )

Earth connection. Connect the shield of the ATS COMMS cable. At the

other end of the cable the shielding must be connected to one system

earth. See the ATS control panel installation guide. This is not

applicable for the possible shielding of the IADS -bus.

DGP dipswitch settings (see fig ,  & fig )

ADDR DIP switches 1 to 4 are used to identify the DGP number to

the ATS control panel. Select the required DGP number and

set the address DIP switch as indicated in figure .

LEDs (see fig , )

RX LED flashes to indicate polling data is being received on the

system databus from the ATS control panel. If the LED does

not flash, the control panel is not operational or the

databus is faulty (usually cabling).

TX LED flashes to indicate the DGP is replying to polling from

the ATS control panel. If the RX LED flashes but the TX LED

does not, it indicates that the DGP is not programmed to be

polled in the control panel or that it is addressed

incorrectly.

Connections CON2 (see fig ,  & fig )

PID Connection to all Addressable modules. Requires one + and

one – terminal to be connected. This will provide power

supply and data.

Modules provide for two bus terminals (see ) or only one terminal

(see  & ). The bus loop does not need special termination.

IADS configurations

There are two main configurations:

• Point identification solution based on I/O modules.

• Intelligent addressable detectors solution.

 Due to very complicated cable length calculation, it is not

recommended to combine intelligent addressable detectors

with I/O modules.

Point identification solution

In the point identification solution, only I/O modules (integrated and

standalone I/O) are recommended. In this configuration conventional

detectors with additional IADS modules (AD011/AD111) are used.

This configuration is based on a 4-wire system:

• Data + power for I/O - 2 wires.

• Power for detectors - 2 wires.

The ATS1290 can support 32 inputs in this configuration. Detectors

themselves need to be powered by a separate power supply.

 This is an optimised solution for retrofit.

Intelligent addressable detectors solution

This configuration is based on a 2-wire system:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1290 in the language / languages: English, German, Dutch, Danish, French, Italian, Finnish as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech ATS1290 Manual

Product: