702276
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
Only use units in a clean environment and not in humid air.
5. Installation of ATS1203/ATS1204
(Ref. to figure )
(1) Earth connection. Use also for cable screen and lid
of box.
(2) Processor
(3) Mains power connection
(4) Back-up battery
(5) Pry-off tamper mounting location
To conform with CEI 79-2 regulations at level 2, the
use of the pry-off tamper is mandatory (ST580 or
ST590 kit). Note: The pry-off tamper is not included
with the product.
For detailed information on the PCB, see connection
diagram.
6. Cabling ATS1203/ATS1204 with
control panel ATS2/3/4/4500
(Preferred System databus wiring – refer to figure )
(Refer to the ATS Control Panel installation guide for a
more detailed description of the cabling)
The “TERM” link is on the first and last devices on the
system databus. In a “star” wiring configuration, the
“TERM” link is only fitted on the devices at the ends of the
two longest system databus cable runs.
(1) TERM link fitted (first device on local databus)
(2) Control Panel ATS20/26/30/36/40/45/4600
(3) ATS1105 LCD RAS (TERM switch not set to ON)
(4) Separate 12 V power supply. (Required if RAS is
more than 100 m from the nearest panel or DGP.
Connect “-“ to “-“ of the databus.)
(5) Preferred data cable type is WCAT 52 (2 pair
twisted).
(6) TERM link fitted (last device on local databus)
(7) Earth connection to connect shield*
(8) Any data gathering panel like ATS1201, ATS1203,
ATS1210, ATS1220 or ATS1250.
*Connect cable shield to one device only.
See: System databus connection and Earthing details on
page 5 and 6.
7. Connection diagram
ATS1203/ATS1204 (ref. to figure )
(1) AC connection from transformer
(2) System earth (see details page 6)
(3) 12 V battery
(4) Earth connection for cable screens (shields)
(5) Auxiliary power supply output
(6) System databus
(7) Normally closed panel tamper contact
(8) Normally closed panel tamper contact
(9) Normally closed Alarm Contact
(10) Normally Closed Tamper Contact
(11) Interface to ATS1202 input expanders
(12) External 8 Ohm siren speaker or siren
(13) 1K resistor must be fitted if external siren not
connected
(14) Clock-out Interface to plug on output expansion or
4-way non-clocked output expansion (e.g.
ATS1810).
(15) Dipswitch to set DGP Address
(16) Link to select +12Vdc to output board
(17) Link to terminate databus
J1 RS485 system databus & box tamper
connections.
J5/J6 Zones
J7 Interface to ATS1202 input expanders
J8 Clock-out Interface to plug on output
expansion or 4-way non-clocked output
expansion (e.g. ATS1810).
J13 External siren
J14 Auxiliary power output.
J17 AC connection from transformer and battery
power
8. Important notes
1. If the battery load resistor is enabled, the 8
th
output
is no longer available for non-clocked output
expansion boards.
2. In case the DGP is set for 2 DGP’s to enable all 32
outputs, the control panel programming should be
set up to poll the DGP address and the address + 1.
9. Links
TERM Termination of databus. Only to be used on
first and last device on the local databus.
+12V Connect +12VDC to output board
10. DGP dipswitch settings (ref. to
figure )
Address Select DGP address. Set switches 1 - 4 to
OFF to disable the DGP. (See fig. 2 for
correct address settings.)
11. LEDs
Tx Red LED flashes when remote units (RAS
and DGP) are replying to polling.
Rx Yellow LED flashes when panel is polling
remote unit(s). It must always be active.
12. System databus connection
The system databus is used to connect Data Gathering
Panels (to provide extra zones) and Arming Stations to the
ATS control panel. Remote devices can be up to 1.5 km
from an ATS control panel.
Arming stations and Data Gathering Panels must be
connected via a 2 pair twisted shielded data cable from the
system databus connection. (WCAT 52 is recommended)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS1203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1203 in the language / languages: English, French, Italian as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info