702270
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
KOMMUNIKASJONSTILKOBLINGER (FIGUR A, TERMINAL J3)
Strømforsyning. Hvis avstanden mellom
betjeningspanelet og sentralapparatet ikke overstiger
100 m, kan betjeningspanelet strømforsynes med
Comms + og - fra sentralapparatet. I motsatt fall bruker
du aux-strøm fra US-er eller en ekstern strømforsyning.
D+ De positive og negative datatilkoblingene til databussen.
D - Fjernenheter kan være inntil 1,5 km fra ATS-
sentralapparatet.
IN En åpne-knapp (normalt åpen, pulserende trykknapp)
kan kobles mellom "IN" og "-". Når denne trykkes,
kontrollerer den åpne-funksjonen.
OUT Åpen kollektor-utgang, maksimalt 50 mA. Det er den
første utgangen til utgangskontrollgruppen som er tildelt
dette betjeningspanelet.
DIP-BRYTERINNSTILLINGER FOR BP (FIGUR A)
SW1 - Dip-brytere
Disse brukes til å identifisere BP-adressen. Du finner innstillinger
på figur B.
SW2 "A, B, C, Term"
Disse brukes til å terminere databussen og aktivere andre
forskjellige funksjoner, som beskrevet nedenfor:
SW2-1, A område 9-16
OFF 8-områders-LED-ene viser status for områdene 1 til 8.
ON 8-områders-LED-ene viser status for områdene 9 til 16.
SW2-2, B Bakgrunnsbelysning på betjeningspanel
OFF Bakgrunnsbelysningen på betjeningspanelet slukker
etter en viss tid.
ON Bakgrunnsbelysningen på betjeningspanelet er alltid på.
SW2-3, C Format på magnetkort (kun ATS1105)
OFF ATS-format
ON Ikke-ATS-formater.
(f.eks. kredittkort, alle kort med data på spor 2).
SW2-4, TERM
OFF Ikke den siste enheten på databussen.
ON Terminerer databussen hvis denne BP-en er den siste
enheten på databussen. Se også i
installasjonsmanualen for ATS-sentralapparatet.
LESERTILKOBLINGER (KUN ATS1105) (FIGUR A, J2)
+5 V spenningsforsyning og datatilkoblinger for ATS-
magnetkortlesere (kun ATS1105).
1. D1/D Read data pulse / Wiegand D1-linje
2. D0/C Read clock pulse / Wiegand D0-linje
3. GND (0V)
4. +5 V
5. +12 V
Ekstra funksjonalitet
- Juster LCD-kontrast, ved å trykke på Menu *-knappen
samtidig som pil opp/ned-tastene
- For å justere lydstyrken til summeren taster du Clear og
Ç for å øke lydstyrken, og È for å redusere lydstyrken
RAS LCD de 8 áreas
MONTAJE DE LA UNIDAD
Asegúrese de que el teclado está sobre una superficie plana para
evitar activaciones indebidas del interruptor tamper.
Monte la caja de la unidad con tornillos. Ajuste el PCB con el
tornillo suministrado. Ajuste la tapa del teclado con el tornillo
suministrado.
Si es necesario instalar un tamper de intromisión, utilice un tornillo
que encaje en la parte trasera del teclado (vea la ilustración A, ).
CONEXIÓN DEL TECLADO AL PANEL DE CONTROL
(ILUSTRACIÓN A)
Consulte el manual de instalación del panel de control para
obtener instrucciones.
LED (VEA ILUSTRACIÓN A)
Rx Este LED parpadea para indicar que se están recibiendo
datos de sondeo en el bus de datos del sistema desde
el panel de control ATS. Si el LED no parpadea, bien el
panel de control no está operativo o bien el bus de datos
está defectuoso (suele ser un problema de cableado).
Tx Este LED parpadea para indicar que la estación de
armado (RAS) está respondiendo al sondeo realizado
desde el panel de control ATS. Si el LED Rx (Rx0)
parpadea y el LED Tx (Tx0) no lo hace, significa que la
estación de armado remoto (RAS) no está programada
en el panel de control para ser sondeada o se está
direccionando incorrectamente.
INDICACIONES LED EN EL TECLADO
Área Cuando las áreas 1 a 8 (o 9 a 16) están armadas, se
encienden 8 LED rojos. En caso de alarma,
producirá destellos intermitentes (si están armadas)
o destellos (si están desarmadas).
Alimentación Cuando la alimentación de 230 V CC está
conectada, se ilumina un LED verde.
Alarma En caso de que se produzca una alarma, sea del
tipo que sea, en un área asignada al teclado, se
ilumina un LED rojo.
Fallo En el caso de que se produzca un fallo en el
sistema, se iluminará un LED amarillo.
CONEXIONES COMMS (ILUSTRACIÓN A, TERMINAL J3)
Fuente de alimentación. Si la distancia entre la estación
de armado y el panel de control no supera los 100 m, se
puede suministrar alimentación a la estación de armado
mediante las conexiones Comms + y – del panel de
control. De lo contrario, utilice AUX PWR del DGP o una
fuente de alimentación auxiliar.
D+ Conexión de datos positiva y conexión de datos
negativa del bus de datos.
D- Las unidades remotas pueden estar a una
distancia máxima de 1,5 km del panel de control ATS.
IN Se puede conectar un pulsador de petición de salida
(interruptor de pulsador momentáneo, normalmente
abierto) entre “IN” y “-“. Cuando se presiona, este
pulsador controla la función de petición de salida.
OUT Salida de colector abierto, 50 mA como máximo. Es la
primera salida del grupo de control de salida que se
asigna a esta estación de armado.
CONFIGURACIÓN DE CONMUTADORES DIP DE RAS
(
ILUSTRACIÓN A)
Conmutadores DIP SW1
Se utilizan para identificar la dirección de la RAS. Vea los detalles
de la configuración en la ilustración B.
“A, B, C, Term” SW2
Se utilizan para terminar el bus de datos y habilitar otro grupo de
funciones, como las que se describen a continuación:
SW2-1, A Áreas 9 a 16
OFF Los LED de las 8 áreas muestran el estado de las áreas
1 a 8.
ON Los LED de las 8 áreas muestran el estado de las áreas
9 a 16.
SW2-2, B Retroiluminación del teclado
OFF La retroiluminación del teclado excede el tiempo
asignado.
ON La retroiluminación del teclado permanece encendida
continuamente.
SW2-3, C Formato de la tarjeta magnética (sólo unidad ATS1105)
OFF Formato ATS
+12
0V
+12
0V
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1100 in the language / languages: English, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info