655849

Ariston PROfessional TECH-serie Manual

54
Zoom out
Zoom in
Previous page
1/68
Next page
54
GB
Picture 15 – PROfessional TECH: lights
Green indicator light ON – Red indicator light
OFF:
Red indicator light ON:
Contact your
installer.
Green indicator light OFF:
The boiler
is no longer protected against corrosion.
Contact the installer.
Picture 15a- HPC - QUIE
Green indicator light : light ON or flashing
light =
Light OFF =
anti-corrosion protection
defect : replace the battery NIMH 9V. If the
defect goes on, contact your installer.
Orange indicator light:
Light ON= under heating
Light OFF = out of heating
If connected to the mains with a dual timer schedule
or exclusive night-time schedule (only for models
with battery), the green indicator light switches on
but is very weak for the first 48 hours in accordance
with the charge status of the battery. Check the
indication light after 48 hours of operation.
In order to guarantee full boiler
protection (green light illuminated),
any faulty batteries must be replaced.
If the batteries are not replaced, the guarantee
will become void. It makes good sense to replace
them once they have been used for one or two
years.
MAINTENANCE AND REPAIRS
1. Maintenance
Empty the appliance annually (twice a year if the
water has been treated with a softening agent)
in order to:
1. check the condition of the magnesium anode;
2. remove all deposits inside the boiler.
We strongly recommend that the performance
of the water softener is checked regularly. The
residual hardness cannot be lower than 15ºf.
A water hardness level which is too low will
cause the guarantee to become void.
1.1. Emptying
➢ Cut off the electricity supply before performing
any work on the appliance.
➢ Shut off the cold water supply at the inlet.
➢ Open the hot water tap to draw water.
➢ Open the emptying valve on the safety assembly
and the water will flow out of the drainage hole.
1.2. Build-up removal – Checking the anode
➢ Empty the appliance (see above).
➢ Remove the protection element and unscrew
the base (some residual water may leak out).
➢ Clean the boiler: without using metal objects
or chemical agents, remove any build-up on
electrical elements or on the bush (steatite), on
the corresponding casing and on the base of the
boiler.
➢ If a magnesium anode is used, check its
condition: the magnesium anode is consumed
progressively in accordance with the water quality,
in order to prevent corrosion of the boiler. If the
diameter is smaller than 15 mm (for the armoured
range) / 10 mm (for the steatite range), or if the total
volume is lower than 50% of the initial volume, the
anode should be replaced.
➢ Use a new seal every time the base is
replaced after being removed.
➢ When screwing in the bolts
again, use a “cross-
tightening” technique. The tightening torque should
be between 7 and 10 Nm.
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston PROfessional TECH-serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston PROfessional TECH-serie in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info