Manual Ariston LL 65 S NA (page 7 of 36) (English)

34779

Zoom out

Zoom in

1/36

ARISTON DISHWASHER - User Manual 5

www.aristonappliances.us

You have loaded your dishes and you now have to set

the wash cycle. It takes just one minute to learn how

Starting the dishwasher

You can cancel the

wash cycle in progress,

if it has only just started.

Make sure the wash

cycle has ended before

removing the dishes!

After performing all the

operations described in the

previous paragraphs press

on-off button "A": indicator

light "B" comes on.

Selecting the wash cycle.

To select the wash cycle

press button "P". Each time

you press the button, a

beep will sound and

indicator lights "E" will light

up in sequence: choose the

cycle you deem most

suited to the type of dishes

to be washed (have a look

at the wash cycle table on

page 7). If the appliance

door is shut, press the Start

button "R" and you will hear

a beep; the cycle will start

up within a few seconds.

The dishwasher keeps you

informed.

Your dishwasher is fitted

with indicator lights (G)

which light up to indicate

the cycle phase under way.

prewash,wash,rinsing,

drying. At all times, your

dishwasher tells you which

cycle phase is under way.

Modifying a wash cycle in

progress.

If you have chosen the

wrong cycle, not to worry!

You can modify the wash

cycle in progress, if it has

only just started.

Keep the RESET button

"R" pressed for about 5

seconds: a prolonged beep

will sound, followed by

three short beeps. Indicator

light "G" will turn off and at

this stage, all the settings

will have been cancelled.

You are now free to re-set

the correct wash cycle.

You've left out a dish?

Well, it happens to

everyone. Interrupt the

wash cycle by pressing the

ON-OFF button, insert the

dish you had forgotten and

press the ON-OFF button

again. The cycle will start

up from where you

interrupted it.

Finished?

The end of the wash cycle

is indicated by two short

beeps and the flashing of

the drying phase indicator

light.

The end of the wash cycle

is indicated by two short

beeps and the flashing of

the drying phase indicator

light.

Turn the appliance off by

pressing button "A", thus

cutting off the electricity

supply.

 If accessible turn off the

water tap

 Wait a few minutes

before unloading the

dishes: they are very hot!

If you wait a little while,

they dry better thanks to

the steam.

Empty the lower rack

first.

There's been a power

failure? Have you opened

the dishwasher door?

The wash cycle stops and

then restarts when the

electricity comes back on

or when you shut the door.

Everything is under

control!

If opening

the door

soon after

the end of

the program, or during

it, stand away from the

Dishwasher, to avoid

possible injury from

hot steam.

You decide when it starts.

When you have loaded the

dishes, you can choose

when to start your

dishwasher before setting

the wash cycle desired.

Press button "D" to delay

the start of the wash cycle

by 12, 9, 6 or 3 hours.

Each time you press it, you

will hear a short beep and

the indicator light "G"

corresponding to the

selected delay will light up.

Now you can select the

desired wash cycle. Press

the start button "R" and

after you hear the beep, the

countdown to the delayed

start will begin.

Once this time is up, the

indicator light will stop

flashing and the wash cycle

will begin.

If you have set a 12 hour

delay, for example, once

you have selected the

wash cycle, the 12 hour

indicator light will flash

followed by the others in

sequence until the set time

delay is up. A quick look at

the indicator lights will keep

you informed of the

countdown progress at all

times.

Have you changed your

mind?

If you change your mind,

you can set a shorter time

delay: press button "D" to

select it. You need not reset

the wash cycle.

If on the other hand you

want to cancel the delay

set and you want the

cycle to start immediately,

press button "D"

repeatedly until the cycle

starts and indicator light

"G" corresponding to the

cycle start phase comes

on.

Dual function of indicator

lights "G"

1) flashing to indicate a

delayed start: to remind

you that you have set a

delayed start;

2) on and not flashing

beneath the cycle phase

symbol:

meaning the cycle has

started and is in the phase

indicated by the symbol.

You want to wash on the

upper rack only?

Remember to use half the

amount of detergent.

Your dishwasher also

allows you to wash half a

load, to save water and

electricity.

Before setting any wash

cycle whatsoever, press

button F to select that

you want to run a half cycle

on the upper rack.

When you press it, you will

hear a beep and indicator

light H corresponding to

the selected function will

come on.

Would you like to see which

settings you have made?

At any time, when the

cycle is under way, if you

press button "P", the cycle

in progress indicator light

will light up for a few

seconds, followed by the

half load indicator light,

wherever set.

Ready, steady, go!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston LL 65 S NA in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston LL 65 S NA Manual

Product: