454485
17
Zoom out
Zoom in
Previous page
1/80
Next page
ARISTON DISHWASHER - Instructions for installation and use
15
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Make sure the
wash cycle has
ended before
removing the
dishes!
If opening the door
soon after the end
of the
programme,or
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
steam.
First of all.
After performing all the operations
described in the previous para-
graphs, turn the water tap on com-
pletely, open the appliance door and
press ON-OFF button "A": indica-
tor light "B" comes on. Your appli-
ance is now on and awaiting in-
structions.
Selecting the wash
cycle.
Select the wash cycle by pressing
button "P". Each time this button
is pressed, one of the indicator
lights "M" will come on in sequence,
select the wash cycle you deem
most suitable for the type of dishes
to wash (take a look at page 17,
where you will find the wash cycle
table). Close the appliance door and
after a few seconds, you will hear
a short beep: the wash cycle has
begun.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Open the appli-
ance door carefully to avoid any
hot water splashes, then keep but-
ton "P" pressed for approximately
5 seconds, until you hear 3 short
beeps. Indicator light "M" will come
off and at this point, all the settings
will have been cancelled. You are
now free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by opening the
appliance door with the utmost
care, as usual, then insert the dish
you had forgotten. When you shut
the appliance door, the cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is indi-
cated by a double beep and the
flashing of the wash cycle indicator
light "M".
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam.
Empty the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
Everything is under control!
You can modify
the wash cycle in
progress, if it
has only just
started.
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired.
Press button "C" to delay the start
of the wash cycle by 2, 4 or 6 hours.
Each time you press it, you will
hear a short beep and indicator light
"D" corresponding to the selected
delay will come on.
Now you can select the desired
wash cycle.
Close the appliance door and, after
you hear the beep, the countdown
to the delayed start will begin.
Once this time is up, indicator light
"D" will stop flashing and the wash
cycle will begin.
Ready, steady, go!
If you have delayed the
start of your wash cycle,
it is best if you do not
modify anything while
you wait during the
countdown.
If you really have to,
then press button "P"
and keep it pressed down
for approximately 5
second You will hear 3
short beeps and all the
settings will be cancelled.
You can now repeat the
programming operations.
Have you changed your
mind?
If you change your mind and you
wish to set a different delay, just
open the appliance door, press
button "C" and repeat the selection.
If on the other hand you want to
cancel the delay set and you wish
to start the wash cycle
immediately, press the button in
sequence until indicator light "D"
comes off.
Once you close the appliance door,
the wash cycle set previously will
begin.
Warning!
Open the dishwasher door,
turn off by pressing button A,
unplug the appliance from the
electricity socket to cut off the
power supply; the power supply
cable should consequently be
easily accessible.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston LI 480 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston LI 480 A in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 13,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info