Manual Ariston LBE68 (page 19 of 56) (English, German, French, Italian)

23752

Zoom out

Zoom in

1/56

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Using the Drilling Template.

- To trace the positions of the holes on the left-hand side

of the panel, align the drilling template to the top left side

of the panel using the lines traced on the extremities as a

reference.

- To trace the positions of the holes on the right-hand

side of the panel, align the drilling template to the top

right side of the panel.

- Use an appropriately sized router to mill the holes for

the two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part of the

hinge must be positioned facing away from the panel) and

fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side

of the hinges and fasten it with the two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow in fig. 2)

into the hole for the hinge and push the panel towards the

front of the machine. Fasten the two hinges with the type

D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of modular

cabinets, mount either one or both of the guides for the

base molding (as shown in fig. 8). Adjust them for depth

based on the position of the base molding, and, if

necessary, fasten the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q into

the special slot and once it is in the desired position, lock

it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to raise the machine to the

appropriate height.

- To adjust the position of the wooden panel in both the

vertical and horizontal directions, use the C and D

screws, as shown in fig. 7.

Important: close the lower part of the appliance front by

ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height adjustment.

The following can be found inside the polystyrene lid (fig. 10):

2 crossbars (G), 1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from 815 mm

to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed higher than

the above height, you need to use the following accessories

to raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4

nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at the front of

the appliance, fastening it in place using screws I (screwing

them in where the original feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance from 835

mm to 870 mm.

Once you have reached the desired height, lock nuts L onto

crossbar G.

To adjust the appliance to a height between 870 mm and

900 mm, you need to mount strip M, adjusting feet H to the

required height.

Insert the strip as follows:

loosen the three screws N situated at the front of the Top

cover of the appliance, insert strip M as shown in fig. 12,

then fasten screws N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston LBE68 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston LBE68 Manual

Product: