454756
11
Zoom out
Zoom in
Previous page
1/26
Next page
11
Important: the appliance must be disconnected from the
power supply before making any adjustments or
performing any maintenance, etc.
Installing built-in ovens
To insure that your built-in oven operates properly, the
cabinet must have the proper characteristics. The
dimensions of the cabinet opening are indicated in figure;
595 mm.
595 mm.
20 mm.
543 mm.
5 mm.
567 mm.
23 mm.
593 mm.
45 mm.
558 mm.
595 mm.
595 mm.
20 mm.
543 mm.
5 mm.
567 mm.
23 mm.
575-585 mm.
558 mm.
595 mm.
45 mm.
min.
45 mm.
min.
These dimensions apply for installation both beneath the
counter and overhead. To ensure adequate ventilation, the
opening should not have a back panel. Preferably, the oven
should be positioned on two strips of wood. If the support
surface is continuous, it must have an opening of at least
45 x 600 mm.
560 mm.
45 mm.
To fix the oven to the cabinet, open the oven door, insert
the 4 wood screws into the 4 holes on the perimeter of the
frame, and tighten them (only a few models). The panels
of the adjacent cabinets must be made of heat resistant
material. In particular, the glues used in cabinets covered
with wood veneer must resist temperatures of up to 100°C.
In compliance with safety regulations, once the appliance
is installed there must be no contact with electric parts.
All the parts designed to ensure protection must be
fastened in such a manner that a tool must be used to
remove them.
Fastening the Oven to the Cabinet
1. Position the "A" brackets so that they are flush against
the oven support strips (B).
2. Position the cleats (C) on the "A" brackets as shown
in the figure so that the thickness of the sides of the
cabinet, indicated on the cleat, is facing you.
3. Fasten the brackets and the cleats to the edge of the
side of the cabinet using the "D" screws.
4. Fasten the oven to the cabinet using the screws and
plastic washers (E).
D
A
B
D
D
18
16
18
16
18
16
18
16
18
18
18
18
C
C
C
E
E
Electric Connection
Ovens with a three-pole power supply cable are designed
to operate with alternated current at the supply frequency
and voltage indicated on the data plate (at the bottom of
the oven dashboard). The earthing conductor of the cable
is the yellow-green conductor.
V
Feeding cable installation
Terminal blok opening:
l Unscrew screw V
l Pull and open the junction blok lid
For the installation of the feeding cable carry out the
following operations:
l unscrew the screw of the cable stop and three screws
of the contacts: L-N-( ).
l fix the small cables under the heads of the screws
remembering to observe the colours: Blue (N) Brown
(L) Yellow-Green ( )
l fix the feeding cable in the special cable stop and close
the cover.
Installation
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston FM 22 M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston FM 22 M in the language / languages: English, French, Italian as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info