Manual Ariston FDD 9640 (page 8 of 72) (English, German, Dutch, French, Turkish)

604765

Zoom out

Zoom in

1/72

How to run a wash cycle or a

drying cycle

1. SWITCH THE MACHINE ON. Press the On/Off button

; the text POWER ON will appear on the display and the

START/PAUSE indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load the

laundry, making sure you do not exceed the maximum load value

indicated in the table of programmes on the following page.

3. MEASURE OUT THE DETERGENT. Open the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each wash

cycle; these may be adjusted. The duration of the cycle will

appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modifying the temperature. The machine automatically

select the maximum temperature set for the selected

wash cycle; this values cannot therefore be increased. The

temperature can be decreased by pressing the button,

until the cold wash “OFF” setting is reached. If this button

is pressed again, the maximum values are restored.

! Exception: if the 2 (40°)

(2nd press of the button)

programme is selected, the temperature can be increased

up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected programme, press

the corresponding button repeatedly until the required

delay period has been reached. When this option is

enabled, the symbol lights up on the display. To remove

the delayed start function press the button until the text

“OFF” appears on the display.

Setting the drying cycle.

The desired drying cycle type may be set by pressing the

DRYING button once or several times. Two options are

available:

A - Based on the how damp the clothes are once they

have been dried:

Iron: suitable for clothes which will need ironing afterwards.

the remaining dampness softens creases, making them

easier to remove.

Hanger: ideal for clothes which do not need to be dried fully.

Cupboard: suitable for laundry which can be put back in a

cupboard without being ironed.

Extra: suitable for garments which need to be dried

completely, such as sponges and bathrobes.

B - Based on a set time period: between 20 and 180 minutes.

To exclude the drying phase press the relevant button until

the text OFF appears on the display.

If your laundry load to be washed and dried is much greater

than the maximum stated load, perform the wash cycle, and

when the cycle is complete, divide the garments into groups

and put some of them back in the drum. At this point, follow

the instructions provided for a “Drying only” cycle. Repeat

this procedure for the remainder of the load. A cooling-down

period is always added to the end of each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle ( - -

) in accordance with the type of fabric. The desired drying

level or time may also be set using the DRYING button .

Selecting the cotton drying cycle through the programme

selector knob and pressing the “Eco” button activates an

automatic drying cycle that allows for saving energy, thanks

to an optimal combination of air temperature and cycle

duration; the display will visualise the “Eco” dryness level.

Set the desired wash intensity.

Option makes it possible to optimise washing based on the

level of soil in the fabrics and on desired wash cycle intensity.

Select the wash programme: the cycle will be automatically

set to “Normal” as optimised for garments with an average

level of soil (this setting is not applicable to the “Wool” cycle,

which is automatically set to “Delicate”).

For heavily-soiled garments press button until the “Super

Wash” level is reached. This level ensures a high-performance

wash due to a larger quantity of water used in the initial phase

of the cycle and due to increased drum rotation. It is useful

when removing the most stubborn stains.

It can be used with or without bleach. If you wish to bleach the

items insert the additional compartment (4) into compartment

1. When pouring the bleach, be careful not to exceed the “max”

level marked on the central pivot (see figure pag. 10).

For lightly-soiled garments or a more delicate treatment of the

fabrics, press button until the “Delicate” level is reached.

The cycle will reduce the drum rotation to ensure washing results

are perfect for delicate garments.

Set the rinse type.

Option makes it possible to select the desired rinse type

for sensitive skin. Press the button once for the “Extra Rinse”

level, which makes it possible to select an additional rinse after

the standard cycle rinse and remove all traces of detergent.

Press the button again for the “Sensitive Skin” level, which

makes it possible to select two additional rinses to the standard

cycle rinses; it is recommended for very sensitive skin. When

the button is pressed for the third time, the “Anti allergy Rinse”

level is set, thus allowing the selection of 3 rinses in addition

to the standard cycle’s rinses. The option - started with cycles

at a temperature of 40°C - makes it possible to remove major

allergens such as pollen, cat and dog hair. With cycles at a

temperature higher than 40° a very good level of antiallergic

protection is achieved. Press the button again to go back to

the “Normal Rinse” rinse type. If the current adjustment can be

neither set nor changed, the display will show “Not allowed”.

Modifying the cycle settings.

• Pressthebuttontoenablethefunction;theindicator

light corresponding to the button will switch on.

• Pressthebuttonagaintodisablethefunction;the

indicator light will switch off.

! If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash and

the function will not be activated.

! If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will flash

and only the second function will be activated; the indicator

light corresponding to the enabled function will remain lit.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light will become green,

remaining lit in a fixed manner, and the door will be locked

(the DOOR LOCKED symbol will be on). During the wash

cycle, the name of the phase in progress will appear on

the display. To change a wash cycle while it is in progress,

pause the washer-dryer using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

orange colour); then select the desired cycle and press

the START/PAUSE button again. To open the door while a

cycle is in progress, press the START/PAUSE button; if the

DOOR LOCKED symbol is switched off the door may be

opened. Press the START/PAUSE button again to restart the

wash cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “END OF CYCLE” on the display; when the DOOR

LOCKED symbol switches off the door may be opened.

Open the door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button. The cycle will be stopped and the

machine will switch off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston FDD 9640 in the language / languages: English, German, Dutch, French, Turkish as an attachment in your email.

The manual is 4,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston FDD 9640 Manual

Product: