Manual Ariston E-Combi One (page 37 of 80) (English)

719960

Zoom out

Zoom in

1/80

/ 37

COMMISSIONING

OFF

Dans le cas d’une dureté de l’eau

supérieure à 20 °f, prévoir un traitement de

’eau.

Bij waterhardheid van meer dan 20

°f, een waterverzachter voorzien.

Wenn

der Härtegrad des Wasser über 11°dH (20 °f)

beträgt, ist eine Wasserenthärtung

vorzusehe

Se l’acqua ha una durezza

superiore a 20 °f, prevedere un dispositivo di

trattamento.

En el caso de que la dureza

del agua sea superior a 20 °f, prever un

tratamiento del agua.

Nos casos em que a

dureza da água seja superior a 20 °f, prever

um sistema de tratamento de água.

If the

water hardness is more than 20 °f, install a

water softener.

V prípade, ze tvrdost vody

presahuje 20 °f, je treba aplikovat vhodnou

úpravnu vody.

Ha a víz keménysége

nagyobb, mint 20°f német keménységi fok,

akkor a víz kezelésér l gondoskodni

kell.

twar

wody jest w

nale

y zainstal

owiednie ur

zenie.

20 °f su sertli

ini geçen sular için su

ıtma tavsiye edilmelidir (su arıtma

teriye aittir).

Daca apa are o duritate

i m

are dacat 20 °f, este necesara tratarea in

labi

l a acesteia.

XXXX

xxxxx

xxx

XXXX

xxx

MIN

MAX

60/80°C

G30 - G31 28/37 mbar

1009942-05

Converting the appliance from Natural gas to LPG

These appliances are designed to operate with different gas

types.

The appliance must only be converted for use with a different

gas type by a Gas Safe Registered installer.

To convert the appliance to LPG:

(use these instructions in conjunction with the Instruction sheet

supplied with the LPG Kit).

Electrically isolate the appliance (g 1)

2. Turn off the gas supply (g 2)

3. Remove the outer case, lower the

front control panel.

4. Remove the silencer (g 3)

5. Disconnect the gas supply from

the venturi assembly (g 4)

6. Inset the correct diaphragm

(depending on the output of the

appliance) into the venturi spigot

(g 5)

7. Reassemble the gas supply onto the venture assembly (g 4)

and reattach the silencer.

8. Turn on gas supply and test for tightness

9. Purge gas supply

10. Turn the electrical supply on to the appliance.

11. Commission the appliance, check the working pressure is

adequate then test and adjust the CO² values at maximum

and minimum output described in the commissioning section

of the appliance installation instructions. Ensure the ue

gas analyser used is calibrated and set for the gas group

the appliance is being

adjusted for.

12. Check the appliance

for gas leaks using

gas leak detection

uid.

13. Afx the label to

the appliance that

is supplied with the

conversion kit.

AUTO function

This is a function which enables the boiler to automatically

adapt its operation routine (the temperature of the heating

elements) in line with the outdoor conditions, in order to achieve

and maintain the requested room temperature conditions.

Depending on the peripheral units connected and the number

of zones controlled, the boiler adjusts its ow temperature

automatically.

The various

corresponding

parameters should

therefore be set (see

adjustments menu).

To activate the function,

press the

auto button.

Example 1:

Single zone system (high-temperature) with on/off room

Thermostat:

In this case the following parameters must be set:

4 21 - Activation of temperature adjustment using sensors

- Select 1 = Basic temperature adjustment

2 44 - Boost Time (optional)

The wait time for the ow temperature increase in steps of

4°C may be set. The value varies according to the type of

system and installation.

If the Boost Time value = 00 the function is not activated.

Example 2:

Single zone system (high-temperature) with on/off room

Thermostat + outdoor sensor:

In this case the following parameters must be set:

4 21 - Activation of temperature adjustment using sensors

- Select 3 = outdoor sensor only

4 22 - Temperature adjustment curve selection

- Select the relevant curve according to the type of

system, installation, heat insulation used in the building,

etc.

4 23 - Perform a parallel curve shift if necessary, increasing

or decreasing the set-point temperature (this may also

be modied by the user, using the heating temperature

adjustment knob, which, with the Auto function activated,

is used to shift the curve in a parallel manner).

Example 3:

Single zone system (high-temperature) with Sensys controller +

outdoor sensor

In this case the following parameters must be set:

4 21 - Activation of temperature adjustment using sensors

- select 4 = outdoor sensor + room sensor

4 22 - Temperature adjustment curve selection

- Select the relevant curve according to the type of

system, installation, heat insulation used in the building,

etc

4 23 - Perform a parallel curve shift if necessary, increasing or

decreasing the set-point temperature. (This may also be

changed by the user by the buttons 8 which, with the

Auto function activated, is used to shift the curve in a

parallel manner.)

4 24 - Inuence of room sensor

- used to adjust the inuence the room temperature has

on the calculation of the set-point ow temperature (20 =

maximum, 0 = minimum).

Note: See page 40 for details on accessing menus.

Is this the manual for the new Ariston E combi One 24 kw LPG Boiler that does not have a pressure gauge on the front panel ? Submitted on 11-8-2023 at 10:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston E-Combi One in the language / languages: English as an attachment in your email.

The manual is 11,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ariston E-Combi One

Ariston E-Combi One User Manual - English - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston E-Combi One Manual

Product: