591457

Ariston CP 65S F8 Manual

17
Zoom out
Zoom in
Previous page
1/84
Next page
3
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
HOOD
900
Min. mm.
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
420
Min. mm.
Fig. C Fig. D
Gas connecting
The appliance should be connected to the gas mains or to
a gas cylinder in compliance with current Norms in force.
Before making the connection, check that the cooker is
regulated for the gas supply you are using. If not, follow
the instructions indicated in the paragraph “Adapting to
different types of gas.” On some models the gas supply
can be connected on the left or on the right, as necessary;
to change the connection, reverse the position of the hose
holder with that of the cap and replace the gasket (sup-
plied with the appliance). When using liquid gas from a
cylinder, install a pressure regulator which complies with
current Norms in force.
Important: Check that the supply pressure complies with
the values indicated in table 1 “Burner and Nozzle Charac-
teristics” since this will ensure safe operation, correct con-
sumption and ensure a longer life to your appliance.
Connection with hose
Make the connection using a gas hose that complies with
requirements set forth by the current standards. The inner
diameters of the pipe are as follows:
- 8 mm for liquid gas;
-13mm for methane gas;
When installing the hose, remember to take the following
precautions:
• No part of the hose should touch parts whose tem-
perature exceeds 50°C;
• The length of the hose should be less than 1500 mm;
• The hose should not be subject to twisting or pulling,
and should not have bends or kinks.
• The hose should not touch objects with sharp edges,
moving parts, and it should not be crushed;
• The full length of the hose should be easy to inspect in
order to check its condition;
Check that the hose fits firmly into place at the two ends
and fix it with clamps complying with current standards. If
any of the above recommendations can not be followed,
flexible metal pipes should be used.
If the cooker is installed according to the conditions of
Class 2, subdivision 1, only a flexible metal pipe which is
in compliance with current safety standards should be used
to make the connection to the gas mains.
Connecting a flexible jointless stainless steel pipe to
a threaded attachment
Remove the hose holder fitted on the appliance. The gas
supply pipe fitting is a threaded 1/2 gas cylindrical male
attachment. Only use pipes and gaskets complying with
current standards. The full length of the pipe must not ex-
ceed 2000 mm.
Checking that the connection is tight
Important: When installation has been completed, check
the pipe fittings for leaks using a soapy solution. Never
use a flame.
Once the connection has been made, ensure that the flex-
ible metal pipe does not touch any moving parts and is
not crushed.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indi-
cated on the data plate. When connecting the cable di-
rectly to the mains, install an omnipolar circuit-breaker with
a minimum contact opening of 3 mm between the appli-
ance and the mains. The omnipolar circuit breaker should
be sized according to the load and should comply with
current regulations (the earth wire should not be interrupted
by the circuit breaker). The supply cable must be in such a
position that no part of it can reach a temperature of 50°C
above room temperature. Before connecting to the power
supply, make sure that:
• the limiter valve and the domestic system can with-
stand the load from the appliance (see rating plate);
• the mains are properly earthed in compliance with cur-
rent directives and regulations;
• there is easy access to the socket and omnipolar cir-
cuit breaker, once the hob has been installed.
N.B.:never use reducers, adapters or shunts since they
can cause heating or burning.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with
respect to the gas for which it was manufactured (indi-
cated on the label attached to the back of the appliance
and to the packaging), follow these steps:
a) replace the hose holder mounted on the appliance with
that supplied in the bag of “cooker accessories”.
Warning: The hose holder for liquid gas is marked 8, the
hose holder for methane gas is marked 13. Always fit a
new sealing gasket.
b) Replacing the burner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 “Burner and nozzle characteristics”).
• Replace all the parts, following the steps described
above in the reverse order.
Instructions for installation
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston CP 65S F8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston CP 65S F8 in the language / languages: English, German, Dutch, French, Italian, Portuguese as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info